Search results

Just an enquiry . Has anyone got an r380 sitting in there garage they don't want ? Might soon need one

Hi Gents A quick and probably stupid question . My td5 wasregate is seized I believe. Should I be able to move it by hand with the vacuum unit attached ? And which way does the vacuum unit go does it push or pull. Thanks guys

Has anyone had dealings with the company L.R .series ? I ordered a part from them but cannot contact them I have emailed and tried phoning but no replies Mick

Afternoon all Well Delilah ( thats my landie) decided to give me a wonderful birthday pressie today by not starting and remotes not working . Yes its the usual culprit YWY000080 but do you think i can find one Does anyone have a secret supply stashed somewhere Can you fit the ywy000080A ? I...

Hi All not needed to ask a question for some time but in need of guidance now. Td5 series 2 manual gearshift appears to be getting tight. Clutch clearance is good but as transmission warms up the gearshift gets tight. Not yet undriveable but boss is driving her today so I will get told its...

Hi Folks Does anyone know if it is possible to replace the drier on the suspension compressor.? Going to do the seals but have found a lot of water in the compressor . Thanks

Hi Folks Anybody got any good recommendations for an injector puller for TD5 10P injectors. Planning on changing the seals and adjusting the injectors but the service tool is hundreds of pounds . Thanks

Hi all Have felt for some weeks now that delilah has been down on power with no noticeable boost from turbo. Today did a smoke test on the intake and she has a leak from the intercooler. Guess I will be scouring the market for one now. Need her running properly for Billing.

Looking for a td5 manual ecu nnn part number Thanks

Good evening folks looking in to getting delilah chipped . She has the ecu starting with msb which according to the nanocom can not be chipped/ programmed and also my ecu has been opened. Can i fit an ecu starting with NNN and reprogramme the injectors ? I have the early 10p engine Many thanks

Sorry Sorry Sorry for this one but it is doing my head in . First error i have bought a replacement key fob from ebay.opened it up and looked at chip for nanocom No direct 6 digit code ( see pic 2 ) So have tried to work it out using bar code Tried several combinations and have now gone...

Hi folks Disco td5 looked low at rear . She doesn't get used much and battery died so purchased a shiny new one. Only really noticed this while driving last night headlights on pointing to high . Checked with nanocom today ride height showed 100 and 103 assuming this is mm. Does anyone know...

Hi All done a search on here and found very little although that does not mean its not here . My cd changer has part number stc50432 on a label on the back and a round connection fitting . All replacement units i have found have a square or oblong connector . Does this mean my audio cd changer...

Another successful day Only had blower speeds 3 and 4 They want over £100 for the genuine replacement however. The multiplug on the rover 25 resistor is the same take the connectors out and put them in the relevant sockets to match the terminals (all marked on old and new). A little work with...

Replaced n/s rear hub today for abs and tc fault since I last disturbed it. All good now suspension will not lift but no warning lights on . Still waiting for my new nanocom to arrive so is anything common that would not put on the light ?

Hi all Does anyone know if the milometer has illumination when the lights are on. If so what bulbs does it take ?

OK Folks I am considering a new set of injectors as the ones in my disco 2 have done 193k and she is a bit smokey.and smells of fuel. What diag tool do I need to recode the ecu and whats best ?

Good morning all Need some help 0n my td5 engine refitting gearbox yesterday noticed wiring to oil pressure switch broken. made up another loom but cannot find the other end to the broken black wire. Tried searching for a wiring diagram but none on here can anyone assist ? thanks guys

Good morning Folks Need the expertise f you people Took the gearbox out of the disco only to find the dual mass has failed. How much play should you have in the input shaft on the gearbox. I can move this one sideways until it touches the thrust bearing sleeve .?

Looking to renew my transfer box Is the oil the same as front and rear diff This is not a diff lock transfer box Thanks