Search results

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. C

    Can you buy roll over bars for a series 2 , if so are they a good fit and where do you get them

    Can you buy roll over bars for a series 2 , if so are they a good fit and where do you get them
  2. C

    Tip over point

    so is that 45 or 60 degrees cus the doors was keeping me in but it felt fairly **** inducing to me
  3. C

    Tip over point

    anybody know what sort of angle you can get a series 2 to lean at before it tips over
  4. C

    Series lll Brake Nightmare

    As Pobby said its your springs, I thought it sounded a little odd but it works, read my string from a couple of weeks ago same problem with the extra fault of a duff copper tube set, also if you have tried to bleed it through several times you may need some fresh brake fluid as it gets dirty...
  5. C

    Bleedin brakes

    Update on the brakes, I tried everything including the easy bleed kit. sure the fluid came through clean but still lost pressure after a short while, in the end I have removed the copper brake lines and fitted a set of flexable brake lines, I measured the length of run using a bit of cable and a...
  6. C

    Project Series 2A

    For getting rid of old paint or other crap I have used either a twist knot wheel or a sanding disc on a small angle grinder, the twist knot wheel is better but not as fast, and use eye protection as the crap comes off in all directions.....good luck
  7. C

    Bleedin brakes

    Nice one thankyou I am off to have another go , have got hold of an easy bleed kit , will check all of the above and try again
  8. C

    Bleedin brakes

    My bleedin brakes refuse to hold pressure in the system, despite the fact or maybe because of the fact that I replaced every componant, everything brake line, flexable hoses ,wheel cylinders and master cylinder is new as part of a rebuild, I have no leaks that I can see and I have bled the...
  9. C

    Twin headlight conversion

    Thanks pobby I have already fitted the halogen units when I rebuilt the front end
  10. C

    Twin headlight conversion

    Thanks for the advice , the wirings no problem my day job is as an electrician I already have a huge battery on it and an alternator conversion is ongoing but i agree that it would spoil the look of a series 2, will try it as standard first and then if needed fit some spotlights with control...
  11. C

    Twin headlight conversion

    Has anybody installed an extra set of headlights into the wings of a series 2, if so is it a good idea, what are the drawbacks, and is it a worth while job
  12. C

    Series lll Brake Master Cylinder, Query?

    contact Brookwells they sell a twin brake/clutch resovours and the master cylinders
  13. C

    series 3 onto series 2 chassis

    Hi RoverRat Dependant upon the price of the doner chassis I would be tempted to bite the bullet and get a series 3 chassis. I am rebuilding a series 2 onto a series 3 chassis but have side stepped some of the problems by fitting a series 3 gearbox. there are some small differances in the...
  14. C

    Do you paint a galv chassis

    Thanks for the advice, especially hiding the galv chassis away from the spud faced low life need to be hung upside down by their balls car thieves, under seal it it must be because I don,t have 10 gallons of hammerite to hand, and my wallpapering wont pass an mot inspection
  15. C

    Do you paint a galv chassis

    I have found a four year old galv chassis for my series 2, because its older its not all bright and shiny, but do i paint it, will it help or am i just wasting my time, and if i do paint it what with as i have heard that some paints react with the galv ??
  16. C

    Solex carb-keep-rebuild-or bin

    Thanks for the info, I have just looked at the price of the adaptor plate to fit a weber in place of a solex .........£68 thats nearly as much as the carb itself
  17. C

    Solex carb-keep-rebuild-or bin

    I have a solex carb on my series 2 thats a little on the fooked side is it worth rebuilding it or is it a better idea to go for the weber conversion
  18. C

    Would you bother?

    Are you kidding of course its worth having a go at bringing it back from the dead. I have just started rebuilding one that was in a worse state than that, as long as the bulkhead is sound around the vents you can get the door pillar and floor repair sections at a good price , if not there are...
  19. C

    Replacement bulkheads

    Nice one Dopey will check it out
  20. C

    Replacement bulkheads

    Thanks Dopey has this guy got a number or a web site , just in case my first idea wont work
Back
Top