Search results

Hi I own a defender 300tdi 90 1995 plate with an original rear washer wiper switch the wipers work fine and run off the front two terminals but the rear & top terminals had no wires connected to them , my question is what are these terminals for ,I'm thinking the top terminal would connect to...

Hi all I own a defender 300tdi 90 95 plate & I'm trying to establish which terminal runs the pump , the front two terminals run the wipers which where connected when I bought the truck , but the top a back terminals had no wires I've since bought a pump and I'm guessing the top terminal connects...

Hi I own a defender 300tdi 90 1995 & I'm due to fit an alisports intercooler which should give me some more power , will the brakes of a 110 puma fit onto my truck to help when it comes to stopping, apologies if there is a post covering this as I've searched but not found any

When I switch on my side lights heat rear screen switch illuminates and no headlights

Found a round two pin connector in-between the rear lights behind towbar on my 300tdi defender, tried to upload an image but a message comes up saying you don't have permission to do this????

Hi , Currently doing the timing belt on my 300 tdi . According to the manuals u set the tension using a dial torque wrench which ain't cheap , considering using a point torque wrench. Anyone got any tips thoughts on the subject . Cheers in advance

Hi all Any one changed the above as I've done mine after mot advisory decided to go down the polybushes route but once fitted don't look right as there's a gap between fixing bracket and rear bush , is this normal? 300tdi 90 1995

Anyone know where I might be able to get some female electrical terminal connectors which slot into the back of the interior fuse box in a 300tdi cheers

Hi all, On checking wheels for any play pre mot found the driver's front to have a lot of play , took the pads out so I could rotate and listen for any rumblings sounded ok so was hoping I cud adjust the lock nuts . On strip down didn't find what I was expecting to find I.e. two locking nuts...

Hi all 300 tdi with 163k on the clock . Recently fitted a oil pressure gauge which is showing 40 psi at idle should be around the 25 psi Mark , any ways according to land rover high pressure cud be due to either a blockage in the oil ways , a blockage in the crankcase ventilation system or a...

Hi all Been trying to wire a switch into the starter relay circuit as a anti theft prevention. So I figured I could cut into the wire which feeds power from the crank position on the ignition barrel which goes to position 85 on the starter relay , so I wired a switch in as above. the switch has...

Hi all. 300tdi 90 Currently taking out the seat box and wanna take park brake off with out having to disconnect at actual drum is it possible to disconnect at hand brake end . Obviously disconnect cable at that end then it looks like you have to prise out a large rubber bung and undo to nuts on...

Hi all, Got a 90 that doesn't like going in reverse until she's been on a run. Tried gear box oil change with no difference . Any got any ideas.

Hi people, Trying to suss out paint code for my truck its red 1995 300tdi and on the vin plate underneath the word paint is BTR 171 but I can't cross referenced that number with out on tinter net . Any ideas ....

Hi All, Joined as a member a while back 2018 I think mainly because my son acquired a defender 300tdi, which I'm buying of him as hes started work in London and I've just loved working on her, didn't particularly like driving her at first but know any excuse. Just for the record it's a 1995...

Hi all Was going to change the oil in the swival pin housing I have a 1995 300tdi, according to the Haynes manual u fill up with 80-90 gear oil untill it comes out of the oil level hole after first draining the old oil. But on inspection there's only a filler plug and no drain plug or oil level...

Hi all passenger door wont open unless you pull release leaver and lift the door locking mechanism. Had a look and it seems to me that that's a threaded bar that can be adjusted to shorten or lengthen the movement of the mechanism, adjusted this several times but still not got it correct . Just...