Search results

Thanks for the welcome , it's nice to feel at home. The engine temperature sensor sounds like a good starting point especially as the temperature gauge was erratic and "stuck on the stop" sometimes but checking the engine it wassn't so hot thaat you couldn't touch the hoses. I'll check those in...

well hello again, four years older and beset with another hiccup which confuses this 75 year old's brain, your collective knowledge would be greatly appreciated. The Lotus Excel hasn't been used much due to my illnesses but I am now getting back into it with renewed enthusiasm. I had the 14CUX...

well hello again, four years older and beset with another hiccup which confuses this 75 year old's brain, your collective knowledge would be greatly appreciated. The Lotus Excel hasn't been used much due to my illnesses but I am now getting back into it with renewed enthusiasm. I had the 14CUX...

well hello again, four years older and beset with another hiccup which confuses this 75 year old's brain, your collective knowledge would be greatly appreciated. The Lotus Excel hasn't been used much due to my illnesses but I am now getting back into it with renewed enthusiasm. I had the 14CUX...

thanks again. You're a star and this forum is fantastic.

yippeeee ! she runs ! New wiring diagram is far more detailed and showed up something on fuel pump relay. It seems that relay is powered and makes its switch thus powering 87 and 87A. Unfortunately the relay we used was powering 87A but switching off 87 simultaneously thereby down powering...

Thanks for the wiring diagram, it may provide the answer. I was working from a 1995 diagram and this one is post 1995. fingers crossed.

Once again, thanks for your thoughts. I have not rechecked the earth on the new fuel pump but will do so on Monday. I have to say that the pump starts its initial 5 second run when the ignition is switched on so I believe the fault to be somewhere in the injector circuit as If the injectors...

I assume that if it were a concealed isolator then the starter motor wouldn't function so I've ruled that out. I wondered about the absence of the inertia switch as there was one originally on the Lotus ( recipient).+ I've installed a 6.8 ohm resistor in the coil + lead and changed the tune...

The ECU is indeed switching the fuel pump relay but nothing beyond . The engine relay is switching as it should and the engine will turn over and fire on the key

....and on it goes ! Position to date is this. The ECU was sent to ECU Technologies for testing and came back A O K , however, the engine won't run unless I run a direct feed to the fuel pump and excite the injectors alternately bypassing the 14CUX. ECU Tech immediately responded that it was...

excellent, thanks for solving that one. It's obviously something I overlooked in an earlier reply...it's an age thing I suppose. Hopefully my next post will be to confirm that the engine runs.

Once again thank you all for your input. I have managed to get a resistor from Rimmers under another part number. I am , however, unable to find a supplier for the 470 ohm tune resistor. A little closer every day !

Thanks gents, I'm afraid I'm still struggling. Terminal 40 on ECU is fuel pump/ engine speed control / lambda sensors and apparently requires a 6.8 K ohm resistor in line. I have been advised that it is not necessary to use the lambda sensors on this application but my local electrician can't...

Final bits of wiring have thrown up a puzzle for me. The wiring diagram for the 14CUX shows fuel relay and main relay with a common brown wwire apparently linking them but it doesn't show the source of power to either one. Are they powered from ignition, alternator, battery or what ? Once again...

Fantastic ..thank you very much.

Many thanks for the information, Rimmers have been able to supply the necessary cable driven tranducer for an LT 77 gearbox so all is well.. I have a further mystery which i hope somebody can solve for me. The 14 CUX requires an input from a fuel purge valve / sensor. I have a wire in the ECU...

Thanks for the response to my enquiry. I have searched all local breakers and a few specialist in the south and southwest to no avail. I contacted the chap whose business was on the link and he was quite helpful. The most successful result came via Rimmer Bros who put me in touch with a company...

Hello, I'm a newbie and don't know my way around here ( actually I'm an oldbie and don't know my way around anywhere ) I am trying to complete a major transplant of a 96 3.9efi serpentine engine/ LT77 box into a 1986 Lotus. The job was started about 6 years ago and has passed through the hands...