Search results

brilliant, exactly what im after. code is camshaft position sensor. the 4.6 should run on the 4.0 map, not the most efficiently but it should be able to compensate. with a 4.6 maf and remap it will though - will be interesting to see the difference when i get this done.

Hello all, After an engine swap (dead 4.0 to 4.6) ive got a P0340 code and subsequent struggling under load. I used my old sensor so im pretty sure it will be a wiring issue. But where does it come from the ECU so i can test it? many thanks!

got a 4.0 disco 2 manual, 140k miles and having issues - suspecting a cracked block and coolant getting in, head gasket was fine. theres a running 4.6 p38 thor engine for sale nearby I can pick up cheap. from a search it seems it will drop strait in and will just need the ecu programming to a...

Just got britpart ones from John craddocks, I'm starting to think some form of gasket either head or manifold.

not sure if youve fixed the issue with the lpg changing to quick but most of the software is available online and the leads for laptop are pretty cheap. same problem on mine and just a case of ajusting the values, mine was set to swap over at too low of an rpm. make sure you save them first...

Hi all, Trying to narrow down and fix this myself before taking it to a garage :mad: hope someone can point me in the right direction. A few weeks ago felt like I lost power while driving. when cold losts of misfires pulling away, improves slighty when warm but a real struggle to get to 60mph...

Ah cheers bud, much appreciated advice!

bump, any ideas anyone

Ive recently had an issue with leaking sunroofs. There all sealed and fixed now but water did get down to the fuze box/idm, Ive fitted a replacement and Ive also had the BCU out and looks fine - no corrosion. As far as the locking problem: The fob does not unlock any door including boot, but i...

Cheers dude! Much appreciated.

Ah cheers that will be a great help.

I'll open a dispute. Bit if you could get me the measurements and I'll bodge something. Cheers dude Edit: just checked I ordered them a while ago and I'm past my 90 days now :-/

Yes those. I assumed they come with the roof rack so I rang the seller but they didn't want to know.

I think so, at the moment there's 2 bolts. But I assume there's a piece that's fits to this and then the roof bar bolts to the piece. Don't know what it looks like.

Hi guys, I brought some roof bars of eBay for my 3 door but when I went to fit it I didn't have any mounting points for the front bits in the roof when you take the little caps off. Where can I get some from? Or can I make some? Thanks.

Tight, took the drum off, was some rusty dust on the shoes, blew it off, put drum back on and now it's fine. Gonna service both the rear brakes soon. Running wise its fine, some blue smoke at first but all gone now. Fixed just in time for mot. Need some new tyres though. It's 18inch sport...

I've smashed the living hell out of it, and been rocking it back and forth so much the non spinning wheel has dug a massive rut aha. Time to get the wheel and drum off methinks.

Cheers guys, I've tried rocking it and trying to just drive with it on but it won't budge. I've taken the centre console off and the left hand side wire won't 'go back in' when the lever is depressed.

Right then, maf cleaned, pipes cleaned, all filters replaced, replacement covers installed and bolted on. Also put in some silicone hoses and put in a blanked egr. Start the car. Runs fine. Rev it a bit, gets past 1800 - great, now time for a test run. Put it into reverse and take of the...

No postman yet so can't get the engine sorted but took the bumper and side wing off, under the wing and around the front headlight area was completly, like enough to pot several plants, caked in wet mud as well as inside the intake hole. All cleaned out now and a inspection panel cover ordered...