Search results

My 110 200Tdi is chucking out loads of exhaust smoke. It is grey and hangs in the air - so I don't think it's the head gasket - the water vapour would disappear pretty quick if it was that. The haynes says to check the injectors by pulling off the union for each injector in turn - apparently...

Having problems with my indicators blowing fuses and think that the hazards might be involved too. I put the hazards on for a minute or so the other day, and then there was a buzzing and then a click from the fusebox - one of the relays, I think. Fearing the worst, I tried the indicators...

My indicators are playing up - if I indicate right fuse 5 blows after a few ticks. I have disconnected the indicator units, but the same thing happens - just after a little bit longer. The horn was not working either - thought it was probably on the same fuse - but no! It is on fuse 1! I...

I have managed to forget to tighten one set of wheel nuts after changing all the wheels for a new set, then drove about 20 miles. Felt a bit odd. Now I know why. C0ck. C0CK. The wheel itself seems OK - measured the diameter of the 'ole and it is the same, give or take a mm, as that...

Dodgy scraping, grinding noise on the way home today... No droning and it did have an MOT last week. But... Jacked the front up and lots of play in the front near side wheel. It has been pulling to that side for a week or so. And it is taking a couple of pumps on the brake to get some...

If I have General Grabber AT 235/85/r16 on three wheels and on the fourth I have a Caiman Black Star Mud 235/85/r16 tyre - will this fail the MOT? Quite different tread patterns, but both are radial... Any ideas? Vulch

I've just changed the rear shoes on my 1993 110 - noticed that the N/S cylinder looked a bit grubby and had probably been leaking at some point. Questions: Can I replace it without pulling the hub? Or will it not fit through the gap? Can I replace the seals and refurb it without...

Like it says in the title - one of either front wheels are locking up and skidding at low speeds (>20mph) under braking on wetish roads. K reg 200Tdi 110. Anyone got any ideas? I know that the front wheels are meant to lock up before the rear, but this is getting stupid. Tyres are General...

200TDi engine - I have changed the master cylinder and have been d1cking about with the nuts on the bolt attaching the master piston to the end of the clutch pedal. What is the function of this adjuster? Will it actually move the friction plate closer to or further from the other bit? Or is...

Crunching into all gears. I know a bit about the hydraulics of the clutch. 1. I have bled it - albeit with a one-man non-return bleeding tube thingy. 2. I changed the slave cylinder about 18 months ago. 3. I have been inside the master cylinder box - the end of the clutch lever(?) is...

I have just had the O/S bulkhead welded but a bit of the seal between the windscreen frame and the bulkhead has perished in the rust and is no longer there! Only about a 4 inch section, to be fair... Shall I just squeeze in some silicone sealant? Or do I really have to get a whole new seal...

Running my 207K 200Tdi on biodiesel - if thats relevant - and have a bit of a leak. It is only the pipes that run between the injectors - don't know what it's called, I'm afraid. Old and very perished, I changed them using some rubber piping from my local motor factors. Problem now is that...

My local biodiesel bloke does bio for £1 a litre, but down to 90p if I buy 500litres! I have found a 1000 litre IBC on fleabay but was wondering how I should get the bio out of the IBC and into the tank! I'm wanting to do this on the cheap, in order to make it pay for itself, so I was...

Right, I am an ar$e. Full of the joys of pouring 83p/l vegetable oil into my 200Tdi 110, I managed to drop the cap from the 6th 3 litre bottle into the fuel tank. C0ck.:mad: I am fairly new to landies, but I imagine there is a fuel filter in line somewhere? If it even gets that far? Will...

Bonnet doesn't match the rest of it, so needs to be painted! How do I remove the bonnet? Is it really as simple as it looks? I've undone the 'folding bonnet prop thing' and pushed it right up parallel with the windscreen. If I lift it, the nearside comes free, but the offside doesn't. Does...

Right, I'm quite new on here - thanks for all your help so far! This is the first actual "ceasing to progress" problem I have had! 110 200TDi. Got it last week. 196K on it. Got home last night and whilst parking up, clutch pedal went hard when in reverse with pedal depressed. Turned engine...

I have just bought what I thought was a 1993 110, but it appears that the body is from something else. I was thinking perhaps a series 2 or 3, although I may well be wrong. Photo attached. I might have some comeback if someone can give me an accurate date for the body. Cheers, Vulch

Right. I need some way of levering my pregnant better half into the front of my 110. I have measured both the door frame and the better half. The door IS big enough. At least at the moment. My landie does not appear to be quite normal anyway, and doesn't have any steps, as I have seen on...

Hello! I've just bought a 1993 110 200TDi CSW! It is a BIT of a mongrel though! But that is sort of what I wanted really. Brown, front end was blue originally - Water Board vehicle I believe. Back section has always been brown - off an old Safari. Mileage is a bit on the high side, at...