Search results

Morning, Will a 300tdi Defender 100amp Alternator (AMR4247) fit a 200tdi Defender? If I take the serpentine belt pulley off and fit the V belt pulley off my old one? Can this be done and is it easy enough? Cheers, Spencer

Thanks, Great video. Cheers,

Ok update: Just phoned Richards and the chassis is at the galvanisers so not too long now. Nearly finished the rear axle. Finish painting the bits I wanted to paint. And the Pool and Darts season is just ready to begin - Roll on late nights and plenty of orange squash. lol

That looks well smart. Can you post the link to where you got it from please Cheers

Ok then, here’s where I’m at. Some Pics below showing the axle in state of rub down. The inside of the Diff and the parts I have taken out apart from the spacer washer which went inbetween the Pinion Flange and the back of the bearing. Still Unsure and need help to understand: Ok then...

Thanks for the advice James Cheers

Some Help please, Once I have put the new output flange in, I need to tighten it - Yes all the info I have looked at states 130Nm but this always shows a nut being tightened up. Mine is a bolt which has a smaller Ø than the nut so I assume should be a lesser torque? If so does anyone know what...

Ok, Some pics, One on the front axle before I started and then finished – can’t get a better pic as it’s tucked away in the garage. Then one of the rear axle draining and some parts off it that have had the crap chipped off, still need to start the other side’s parts. Will need to remove all...

Morning all, Ok then this has been a long time coming and will probably drag on in bits and drabs so bare with me. Don’t know if you are interested in a rebuild thread so let me know and I will stop or carry on. lol? First of all you may remember I got a pair of matching Disco 300Tdi...

Morning all. Started the rear axle build last night - FINALLY Its a rear axle off a Disco 300Tdi. Question is: On the rear calipers i have a Bleed screw and a Brake line nut. But what is the bolt thats in the middle of these for please? Cheers, SpenB

Thanks for the replies, think i will leave it alone then. cheers

Yes - Sorry, I have had another look and it does say tdci. Does that make a big difference or will my stuff still fit?

Hi all, Will the dash panels and gubbings off a 1991 200Tdi fit onto a TD5 2008 Bulkhead? I take it the tunnel will need modding? Cheers, SpenB

Thanks for the replies. I have a 91' 200tdi and the trailing arms are of a 98' 300tdi disco Cheers

Quick question, Are the Rear Trailing Arms off a Disco the same length etc to the Defender ones? In otherwords will they fit my Defender? Have been offered a pair free, wanted to derust and paint then swap over. Cheers.

Ok thanks for the replies. Managed to drill a hole through the head of the bolt then put a small drill in the hole and undo it like a tommy bar.

Morning all, Have now got a Disco 300tdi front axle in the garage to refurb at my leisure then I can swap it over. Trying to take the pitted teflon coated swivel ball off. Have managed to undo all but 1 of the 12point 14mm bolts. The remaining 1 is refusing to move but the spanner now goes...

Hi ya, Just a quick one. Finally getting round to swapping the steering box over. I have plenty of Halfords DIII fluid but none of the recomended DII. Can I use the DIII? Will it matter? What the difference? Cheers, SpenB

Just been given a new disco damper free so will try and use it. I am to fit the mount onto the front rod (drag link?) and using the original chassis mount, set the wheels straight half the travel on the damper and fit. hope fully then the damper has equal travel left and right. Does that...

Morning all, Tried doing a search but struggling. Had my new (2nd hand) PAS box delivered yesterday with the staight drop arm. might change over to the disco setup - so if i bought these: Heavy Duty Steering Rods for Range Rover Classic and Discovery 1 - with 4 ball joints Is it then just a...