Search results

Ok bung fitted and around 7 Ltrs of ATF oil in, oil a little warm now and reads a little over so I will wait till tomorrow when I refit the painted gearbox sub frame and have it all supported on its own. I have had her in neutral and idling a added 0.5 Ltrs after the 1st five and just left the...

It takes nothing to say thanks and it always goes a long way. Btw I have ordered a new one I just need to collect it from the post office hope to get the box refilled tomorrow :-) Got to clean off and paint the gearbox cross member and that's it all done Then onto the cam belt and adjust...

I dont know what they are called but some company's can repair them for you. Don't buy Brit part ones had bad experiences with them

It was quite a bit yes I was expecting 5ltrs ok I will stick 5 in and see where we go. Thanks for your help

i removed the old bits from drain hole and its ready to roll. i just need to get a new drain plug and its all good. it was tight as hell in the hole removed it but when replaceing it i niped it up and it gave up. stiil almost done. not looking forward to filling the gearbox via the dipstick...

thanks for your time disco cool

i have fitted a new decat pipe and replaced the auto filter to the truck, unable to test as the drain plug on the auto box has failed, hopeing i can get a new one rather than drill and tap the drain hole:doh:

hi guys can you help i have an issue, it seems someone bodged the drain plug on the gearbox and i now need a new one can i get one on line or dose anyone know the thread size? its not metric i know that much i think its unf. i dont want to drill and tap if i dont have to. cheers

Well I done the gearbox and all fitted went to tighten the bung bolt and it sheared off :-( Any idea where I'll get one from ? On the up side I fitted the decat pipe while I was at it so not all doom and gloom. Recommend remove gearbox brace and it makes the hole job quicker to do :-)

Ok thanks I'll have a look in a bit

yes sorry its a 300 tdi and rave dont want to play on my windows 7 for some reason cheers

morning sorry to trouble you all dropping to trans oil in my auto box and going to change the filter today moved the gearbox mount and going to remove the sump and i cant find the torque settings for the sump bolts once i replaced the filter can someone help please. (haynes have no info)...

Hi there Have you been welding on it yet? Check the main fuses and all the other fuses and relays under the dash. Quite a few issues can happen here have you checked and cleaned the earth straps up to the starter from the battery as this can be an issue. Hope it helps --- I am here...

ok passenger side rear door opens ok from outside so not an issue child lock not on tryed both ways, ill get some springs ordered tonight. drivers side rear door wont open from either side and tryed holding the lock up as well any other ideas on getting in there? cheers

Hi all got a 5 door 96 disco 1 both drivers and passenger rear side doors wont open from the inside and the drivers rear wont open from the outside now. any ideas how to open the rear that dont open from either side? and any ideas what may be wrong thanks for your time

It's platinum inside so that will give you a clue of how much its worth. Cut the steel back to the edges of the cat or some will give you less It's worth a few quid

I don't have wiring diagrams to post sorry. Will it run at say full speed but not 1,2 or 3? Is it the earth supply to the fan apparently a big issue in the wet. Find plug to the fan and remove it then do a continuity check with each pin to chassis. One if them will either beep or give a...

i did it today thanks, used a 41mm bi hex socket and some nuts to lift it once the peg was on the move grrrr! impact gun took the nut out with little effort thank god! ok pulled out the sheild and found the pinion was sloppy and loose in there is it supposed to be? cleaned up the surround...

welcome to the family and have a good xmas

for those of you looking to buy one or thinking of buying one my advice is go for it! i got a sealey 24volt job, well worth every penny so far it just whips nuts and bolts off with no effort, its amazeing i used my braker bar and grunted a bit i used the impact gun and wow no effort and half a...