Recent content by ROY_H

Completely agree with above. Mike is a number 1 guy. Transformed my Discovery TD5. Explains everything he's doing then stays with you while you test drive in your own time to make sure you're happy with the changes. Tell him what you're looking for, performance, towing, economy he'll sort it.

I have to say I tried a Dastek Chip for a year or two but could never convince myself there was any significant performance gain. had Mike from dynachip work his magic on my '03MY TD5 and it's like a new motor. More go loww down but it just keeps coming. lost that nasty hesitency when you go to...

Just be interested to know if you guys getting more than 26-27 have air-con/ACE/18" wheels fitted. I'm sure one or a combination of these extras causes considerable drag on the consumption.

Reference what to do in regards to insurance, all I can say is when Mike from Dynachip was doing mine, he showed me a date which equates to when the ECU was originally programmed is embedded in the firmware. this should change if an update is made but sometimes..........;)

I actually de-EGRd de-catted and de-centre silencered mine a while back. Hard to say if it did make that much difference performance-wise and yes it does drone a bit when you're towing but it does soumd good pedal-to-the-metal:D

Hi Jagdude, Mike came to me straight after he'd completed yours, arriving spot on time. Really nice guy and very thorough as you say. Agree with you 100%, this is how they should have been out of the box. can't understand what Landrover were playing around at. Certainly finding (when I'm in...

been getting 26-27 general driving, think it drops to about 22 when towing the caravan. Just had a Dynachip re-map so will be interested to see what happens with that (I must keep my foot off the loud pedal:p)

No help to you now I know but I had the same problem with the cross-member bolts so gave up on fitting the de-cat pipe. then I had to put the truck into the local 4x4 specialist in my village and asked him to loosen them up while he was underneath. From what he said this is far from unusual and...

My village 4x4 specialist did it. Dropped tank and replaced pipes. Asked him to loosen the nuts on the exhaust system which were corroded and replaced all the little bolts on the cross-members with stainless allen-heads to make it easire to remove when the time comes. Total bill 178 beer...

Just had to have mine done as it was suffering from exactly the same problem.65000 miles on a 52 plate. Garage dropped the tank to replace the lines and (hopefully) set them up so they won't chafe again (at least in my time!)

I planned to do this ages ago and hit the same problem with the cross-member bolts so gave up. Wagon went into local garage to replace leaking fuel lines above tank this week so asked the guy to sort these out on both the cross members and the rear exhaust bolts which had also seized. Charged me...

This thread carrying on has set me thinking (painful!!). As I said earlier I use an aerial bracket on my roof bars but I noticed my Disco has a seal grommet in a hole in the roof near the back (probably for a GPS aerial). Anyone tried using this to mount a CB twig? Strikes me if the hole is...

I managed to source a bracket that clamps to the roof bars, leading the cable through the door seal. radio is mounted in the dash top-centre (as above) so is easily removable but very handy. because this mounting covers up the speaker I've mounted a small extension speaker to the drivers side of...

If you feel confident you're up to it look here LAND ROVER DISCOVERY TD5 REAR CALIPER SEAL KIT *NEW* on eBay, also, Land Rover, Car Parts, Cars, Parts Vehicles (end time 27-Aug-08 20:58:48 BST) BUT safety critical so be sure you know what you're doing!!

I've got a similar problem with my 2003 S2 but my feeling is it's not the actual gear box but the selector mechanism. When the box gets hot it feels like the gear lever stiffens and the bias springs can't work properly making gear selection difficult. When the box is cool it feels no worse than...