Recent content by PK68

Cheers for that. I'd read stuff about all on thrust side, all not on thrust side, not inline with Conrod, not inline with gudgeon pin!!!!! I thought it couldn't be that difficult or technical! Mine have 3 rings - top, middle and oil ring.

Afternoon all I have an early LR90 with a 2.25 petrol 5MB engine. It's RHD. I've had the engine out and stripped down to try and solve a couple of issues and I'm now putting it back together but I've read conflicting things regarding piston ring gap orientation? Can anyone help? Taking it that...

Hi all I have a 1985 2.25 Petrol Land Rover 90 which seems to have developed a Rear Crank Main Seal leak. It was only quite minor to start with so I've been managing with it for a while. However, now it's leaving a small oil puddle even when parked up and I'm having to regularly top up the oil...

Hi all Thanks for the responses. One of the screws was missing that holds the switch in place. Must have worked it's way out. I got a new switch anyway and fitted it and all seems good so far but I'll let you know if there's any more issues. I had a good check of the loom behind the dash and...

🤣🤣🤣 Cheers. I'll give it a go. Been messing around with it for most of afternoon and is seems to be ok at the mo. But the but at the back where the connectors attach seems quite loose.

Cheers. I'll try that.

Hi all I have an early 1985 LR90 with 2.25 Petrol Engine. The car was fine this morning driving to work but when I came out it had developed the following problem: Problem: With ignition off and key out the Battery Light and Oil Light remain on and the electronic petrol pump continually primes...

Hi It was a ballasted system when I bought it in 2013. I had no clue about these things back then so I bought the standard coil before I knew any different but it ran like crap. After doing some research I realised it was a ballasted system due to how the wiring was connected to the coil. I...

If it's there it's bloody well hidden. A few years ago I had the whole dash off to refurbish it and couldn't see any sign of it. I'll have another dig about. Cheers

Hi Shippers Thanks for that. I'll check it out. I just can't find the actual resistor and I understand that it can just be a wire. I wasn't sure if it was wired differently. The wiring diagrams I have are all for standard systems and checked against my wiring I can't find an extra wire where you...

Just an update. I changed the spark plugs to from cooler BPR5ES to BPR6ES and she's running fine at the mo. Still bubbling at the exhaust though but I think that may be a manifold issue. Still really need to find where the ballast wire runs to from the coil. Can't see it anywhere in the fuse...

Hi all In a bit of a nutshell, I have a 1985 2.25 petrol 90. It's had a few running issues lately mainly relating to fueling and carb issues. I changed jets, etc. And it started running better, just a bit of bubbling at the exhaust which no end of tuning and adjustment would get rid of. So I...

Hi Tom. Hope all is good across the pond in Canada? Sorry for the late response. I ended up buying new jets which seems to have sorted that problem out. However, now it's started with other issues and is back off the road. Thanks for the advice though. Ref the diaphragm, I did change that one...

Hi again all I'm just adding to this thread again as I'm encountering a similar issue again but nothing I've done so far has resolved it. As a reminder it is an early 90 with a 2.25 Petrol 5MB engine. The Problem: Engine dies or hesitates badly on initial acceleration and kangaroos in low revs...

Hi pal. I stripped it back down again and checked the float gap. The gap seemed fine but it looked to me like the float might have been dropping too far allowing all the fuel to drain out before it had chance to refill. I adjusted the tab at the back of the float so it didn't drop as far. After...