As reported elsewhere the mini has been all tuned up on a rolling road. :)
Horrendously expensive (£562) but the results seem to be good. It really does go well now.
What did he find wrong?
1. Incorrect coil (he reports that it had a "points"...
One other small update.
I undid the steering rack U-bolts and installed a "drop bracket" to lower the steering column, then did them up again (of course).
Now I can see all the gauges without leaning forwards in the seat. The auto-cancellation...
I bow to your superior knowledge gents I looked up the Metro engine online and it said:
The standard 1275cc MG Metro engine typically delivers around 57-72 bhp (brake horsepower). A 1275cc engine used in the Metro, which was sourced from the Mini...
Not bad :)
Standard MG Metro 1275 was 72bhp but that was prob at the flywheel
1098cc motor was about 45bhp
Should go well with 62 depending on what diff is in it, :)
Got the Mini back. Drives very nicely without any dramas now. :)
Not a monster by any means. Dyno said 62BHP and 72.6lb/ft
I gave it some beans on the way home on the A130, it felt quite sporty.
Costapacket. :(
Hurt my little finger this morning. Pulling a rotor off a crank shaft and it didn't want to move. When it did it came away suddenly and whacked my finger end against a bolt. Ouch. All hurty now. :(
Rain clouds missed us yesdi. Edgar was livid. Looking at the map todays clouds are moving vertical. We might miss out again.
Me squirrel is still visiting several times a day. He ain't wukked out tis me putting nuts out ferrim. Baby steps. Mesun...
Mornin
Dull and had a sprinkling of rain during the night
Bathroom fitter arrived to sort faults out 🤔
Going to look for narrow landy tyres today, don't know the sizes but daren't ask on here again :)
Skipping breakfast cause I need to loose a...
Trubble is...
With a bit of sawing and welding old screwdrivers can be made into other special tools.
I at the mo have tools in the garage here, in a room and tool box in Frogland and prolly the best ones in the back of the Disco.
So in many...
Ive pulled my tool bag plus all the loose tools out the disco & got tools that ive never seen before, 3 snap on screwdrivers
levers, new hex/alan key/torx bits set. couple of Halfrauds pro spanners 13mm & a 17mm. New blue metal punch.
Wire...
Something I have to do, got a drawer full of screwdrivers, some of em broken, drawer full of many sorts of pliers, drawer crammed with odd sockets and breaker bars, same with another two (at least) toolboxes, all need a serious amount of...
Been in shed sorting out all my tools & evicting everything out my tool boxes thats not a tool, managed to do 2 drawers 🤣 🤣
Ive got some amount of useful stuff that I dont need atm :oops:
Hope they do a good job for you, tell em not to lean it off too much, might look good on emissions but the Mini loves fuel.
It'll be fine, best of luck with it :)
... I have to report that I no longer have GWEN the mini. Awwwwwwwwwwwwwwwwwww. 😢
Because she's at the rolling road tuners. :banana:
May get her back in a day or two later this week and maybe she will go like a :vb-bat: out of Hell or 💩...
Me upstairs water pipes come out me castle wall and all go into a plastic tub fing. It were overflowing when running out the baff. Full ov soap. Ran me baff out slowly and poked the soap wiv a stick to break it up. Roof down pipe runs into it...
Also got some weeds out me manc cobbles. Eye has used many different chemicals. Burnt em. Kicked the top oft. Bleached em. They still grow so eye lifted some cobbles yesdi to pull out the weeds and its root. Some have bin there several years...
Think im in the dog house ?? Not sure as not many words been exchanged this morning. :confused: I'll finish my coffee then
bugger off outside to see what im going to do with that stripped stud. Just wondering if I can get the diff away from the...
D1 taken apart...front axle stripped, yup wrecked a halfshaft both shafts out. Need an offside one, diff still in as
one stud decided it wanted to strip & not come out. :confused: I have spare HD raptor shafts but I aint fitting them as ive sold...
Cut me grass this morning. Then got ready to apply the weed feed n moss killer. But the instructions say don't apply until four days after cutting. So it's still in the sack.