Recent content by cuby

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. cuby

    Disco 2 power steering pump

    No one seems to have found a part number for the correct O ring. I have used your dimensions and found two O rings which I think match. I have added chemical resistance to the requirements. I think we need Viton or Nitrile O rings. Both have a wide resistance to hydrocarbons. Nitrile is listed...
  2. cuby

    SLS Fault but none seen in Hawkeye

    Thanks Sirrafery, I have ordered an ECU off eBay.
  3. cuby

    SLS Fault but none seen in Hawkeye

    Hi Sierrafery I was beginning to think it was the ECU when I wrote the reply to you. Too many odd things happening and no errors logged but the warning lights on. I used two wooden blocks that I borrowed from a chap (He has the Texa diag kit) who as done a few airbags in the past and did follow...
  4. cuby

    SLS Fault but none seen in Hawkeye

    Hi Sierrafery Thanks for replying. 1) Not to start with. The first 3 or 4 tries to calibrate, it looked like it worked but when I disconnected the Hawkeye it just let all the air out and sat on the bump stops. I gave up and tried again a few days later with a Texas which did much the same. But...
  5. cuby

    SLS Fault but none seen in Hawkeye

    Hi I hope you chaps can help. I have got stuck with an SLS fault with my Disco IIa. After I replaced a broken sensor and tried to re-calibrate, I have ended up with two SLS warning lights on the dash. The Off-Road Mode Warning Lamp and the SLS Warning Lamp. Using the Hawkeye ver7, I see no...
  6. cuby

    What could it be?

    Don't forget, a 12v coil is actualy a 6v coil with a ballast resistor in series with it. While you are starting the engine, the battery voltage drops to 10v ish and the ballast resister is bypassed (with a relay) to compensate for the low battery voltage. Once started, the ballast resister is...
  7. cuby

    12,000lb Winch + Pressure Washer

    Went to Slinden today. Winch worked well. Used it about 3 times. @ Bump, you are right, the cable does pile up on one side. We spent a bit of time winding the cable back in nicely. The winch is a bit slow but have to say it does the job. Jet wash also worked well. Self prime is a bit hit and...
  8. cuby

    110 County Chequer Plate - Advice

    Thanks, got pop rivets in, will do that.
  9. cuby

    110 County Chequer Plate - Advice

    Hi I am looking at Britpart DA4071 Rear wing - chequer plate to cover up damage in that area. How should I fit it? Self tapper screws, pop rivet, glue or something else? Thanks Cuby
  10. cuby

    12,000lb Winch + Pressure Washer

    So far so good. Had to nip off the O/S lamp bracket from the winch bumper. Also it has a small black fly lead from the control box which must be connected to the front earth stud. Else the remotes don't work right. Oh one other thing, had to cut the jet wash gear leaver as it hits the winch...
  11. cuby

    12,000lb Winch + Pressure Washer

    Quick delivery, arrived yesterday, it's the thick end of 50Kg and looks the part. Hope I have time at the weekend to fit it.
  12. cuby

    12,000lb Winch + Pressure Washer

    @discodad will do. Not expecting too much from it. It will be quite a contrast to the 8t PTO superwinch on my Defender!
  13. cuby

    12,000lb Winch + Pressure Washer

    I have just bought one and an 8t snatch block. Off to Slinden in few weeks so should get to test out both bits. I asked if they carry spares for it and they said yes. I hope they mean more than a bit of garden hose! From this ebay shop items in Winch Shop store on eBay!
  14. cuby

    Hi Chaps

    I have already taken alot from this web site, so I though it was about time I fleshed out my account and did some posting. I have 3 Landys, a Freebie for day to day running about, an ex utitity 110 for work and a disco 1 for off road toy. Had fun with all of them. When it snows I like to play...
Back
Top