Recent content by Black-Feather

I have fitted Bolt-on bits LED sidelights, indicators, fog etc, and LED relay, easy job but must have a good earths all round and leave the old side indicator bulbs in tucked in the wing helps with resistant ? ? doing HID next but having problems find the relay/resistor that make the dipped beam...

Hi, Yes I'll do that, I perfume that the wires behind the dash on the light will go into the engine compartment somewhere for a lead off, which I can then take off to put the switch in where it should be on the hand brake and then just run wires from the switch to these which I'm guess are an...

I was thinking that might be the case an earth problem, but I still can't see a switch on the hand brake wheres its meant to be? so might have to put one back in, then I'll need to find the wires for it and do a re-wire, I was thinking maybe take out the dash clocks and look at the colour of...

Hi yep just fitted a new 200 sensor and spot on, back to where it always used to be just off middle, I also before the sensor change, put a new 200 gauge in as well so there now right for each other. Now I just have to find out why by hand brake light warning light is staying on all the time...

Yes its works by holding the prop shaft ?

No on the 110 like the Range Rover it works on the prop, I have looked for this switch all over where one might expect to see it, well on normal cars?lol theirs nothing on my hand brake as some have suggested, I have looked around the gearbox area, I cant see anything that stands out there, I...

Hi I was thinking about that, I cant remember now what the thread is as when trying to get one get asked is it fine thread or coarse? ( I have now put a new 200 gauge and still hitting the red so now I have a new 200 sensor to put in to see if that makes any differences in reading? (If not I'll...

Thanks for your reply, I would have never GUESSED that a hand brake on a land rover would work like that.

Hi thanks for the photo just had a real good look around mine nothing there? thanks for your help M B-F

Hi All,,,,Dose anyone no where the hand brake switch might be on a 1988 110 its not on the hand brake its self I have looked there..... once when I use to put on the hand brake the light on the dash went on and off when I took the hand brake off but since I have change the engine from a 2.5 a/n...

Hi all, I have an 1988 110 with the same type of problem? my hand brake light on the dash glows dim all the time and I can't find a switch anywhere near the hand brake, I have top up the brake fluid but the light is still on, it always work ok, until I change the engine from a 2.5 n/a to the...

Hi all, I have an 1988 110 with the same type of problem? my hand brake light on the dash glows dim all the time and I can't find a switch anywhere near the hand brake, I have top up the brake fluid but the light is still on, it always work ok, until I change the engine from a 2.5 n/a to the...

Hi all, I have an 1988 110 with the same type of problem? my hand brake light on the dash glows dim all the time and I can't find a switch anywhere near the hand brake, I have top up the brake fluid but the light is still on, it always work ok, until I change the engine from a 2.5 n/a to the tdi...

Hi thanks for the reply, lost me a bit there ?:doh: understand the steering ok should just be the 4 bolt type... the pump I was thinking of bolting at the side of the block N/S by some sort of bracket? and just put a bigger belt on? Or leave it as it is and end up with arms like pop-pie lol

Hi all,,,, I have a question for those in the no? I have a 1985 2.5 na diesel engine in my 110, and want to fit PAS to it, will the PAS set up from a 90/110 200 tid system, be swap over and fit my 1985 110 na any help would be nice many thanks