Alibro's latest activity

Step-1: Buy the DC Clamp meter recommended by Alibro above. Step-2: Don't try putting a multimeter in-line with the battery feed unless you know what you're doing. Use the clamp meter & note the value after the car is off & locked for at...

The anti-roll bar prevents axle articulation which is good on the road but bad off road. I wouldn't leave them off for long but it should be OK for a test. BTW you probably already know this having replaced so many but when changing drop links...

Lots of off roaders remove the drop links and anti-roll bar completely so why not? Remove the drop links and tie up the ends of the anti-roll bar and see how it is.

A decent FL1 should be between £1k and £2k for a low mileage example so the only reason to throw money at one is for the fun of doing it. I was talking to a guy yesterday who has bought a clean 2003 HSE with 70k for £1300

I had a rattle from a faulty shock absorber a few years ago. The cheapest way to confirm it was to buy a used strut complete from a breaker and swap it out.

Get yourself a DC Clamp meter and test the current draw at the battery, they are very useful tools to have anyway. Something like this one should be OK https://amzn.to/3GzvATs Be wary of using a standard multimeter as the current draw when...

Thanks to all who replied. Ali, I thought for the relatively small amount extra for the full regulator over the repair kit it was worth it. Obviously, in my case I'd have to go motor hunting now. Every day’s a learning day…👍🏻

Not from the water pump, it just drips out. I also had a leak from a plastic hose fitting that had me worried on one car.

Hopefully you have the coolant leak sorted but if still loosing a little, they also commonly loose coolant at the water pump so look out for leaks there.

Honestly, same goal over here, more for green-laning than "off roading" the freelander would not handle it, but if you're up to the task chuck in the same engine, you could probably get an early pre-2001 engine for cheaper, I've got a guide on...

Replaced OSR window regulator. Motor dead in the water. Been in since 2012 apparently. Anyway all done and working again.

The diesel struggles off road without low range to get up steep hills so the petrol will be worse. For green laning or off road racing racing they are good but not so much for extreme off roading.

Well done. I don't think it's common for the original motors to fail but I can't comment on after market ones. I guess someone must have replaced the regulator and motor at the same time in the past. I have to admit I usually order a repair kit...

I was going great ignoring this thread, then today I couldn't help myself and here we are again! Sorry guys, my bad! 🙁

I often wondered where the 5kg option came from. It was always 8kg when I first did the test many years ago.

Off the car should be 1/3 of the time on the car. Due to the 3:1 diff gearing. So 1.2m and 5Kg on the car at a minute is at end of life. I use as a rule of thumb.

Many thanks for that Ali.👍🏻

The rear window regulators are the easiest to repair and there are videos on Youtube showing how.

The rear bushes are usually so hard to remove it's only worth doing if the arms are good. Replacement bushes will need pressing in unless you pay extra for the complete unit and this requires a press.

So long as he's paying the bill just go with it. It's easier that way. ;)

I've never tried testing a VCU that way but it looks kinda tight to me. The scaffold weighs a kilo or two as well as the 6kg weight. In the past I've stuck screwdrivers through the UJ joints to turn a VCU but could never have applied the force...

Looks good. Had a shot at recovering tired door panels this afternoon. Looks to be quite a success.

My old banger £200 daily driver runaround bmw failed the mot today with a knackered subframe. I had a good look at it and the whole rear suspension looks like it's been parked in the sea for some years, so sadly off to the scrappy it goes. It...

And/Or the most bonkers! 🤣 Thanks mate :)

I wouldn't mind so much but the charging timer was only installed a couple of months ago. :( At least it helps me remember how I installed everything in the first place. I spent a few hours rebuilding the HV junction box so it's almost complete...

The rebuild has started. HV and LV junction boxes removed Dumped in a box I was never happy with the previous design that kinda evolved as I learned more about what I needed. I had LV components in the HV JB which is an obvious no no, and...

Not sure whether we should laugh or cry.

Not very often, fortunately, I get "one of those jobs" ! Offered to replace a strut top mount for a mate. Both strut to hub bolts and nuts seized solid, like they had become one piece of metal. My 350 + ft lb impact driver wouldn't touch it. Nut...

Lovely night in work in royal mail an area that noted for being a sweatbox😟 Only thing keeping me going was to ignore it. When all around you are speaking a foreign language I blank it. When I get back home to bed. I eventually ignored the din of...