Latest activity

WTF? 4 would be even betterer!!!

https://www.bbc.com/news/articles/c2d02dz6gedo As no one works a full week in the month of May unless the feast days fall on a weekend, this'll be fun!! And of course if the feast day falls on a Thursday or a Tuesday, then they also take the...

No sadly not… was hoping someone would have had a similar issue and could advise.

2 or even 3..you do know 3 aint an even number :p

What about that blue one on Ebay. lt's an earlier one (but it's got the updated dash which was introduced in 2002) and not the XS so no ABS/aircon etc. ln fact it's the basic SW with vinyl seats and no central locking or electric windows...

Cheers! I think these are the correct RAVE torque settings for the FIP but I can't see the correct torque for the larger threaded bung.

Don't look at me. I have 3 of the sods blocking up my drive now. Need to sell one ...

So looks like you have solved your problem. Wish they were all that easy!! :) :) :)

I'd have to check RAVE next time I have the laptop running but it is less than you think. 90 nm sounds way too much. 25 nm sounds more likely. The high pressure pipes just need nipping up so they don't leak. Finger tips tight using a 17 mm...

It's certainly not local, and after receiving those further photographs and the very helpful input from you both it's definitely a no-go, but it's all good experience. The hunt continues although there's barely any 110s about. It's a big...

2003 L322 td6 Hi folks, Had an issue with an intercooler hose that had come off at the egr valve which I sorted but now I've got a suspension issue. I mention the intercooler pipe because the suspension issue started just after I had the boost...

RAVE says always use a new bolt as it is a stretch bolt. Sone say you can reuse them a few times but I wouldn't risk it!

The chassis is a lot better on this one (no connection to seller l was just having a quick look on Ebay) https://ebay.us/m/goK8l2

Does the handbrake work ,could be something in the drum,shoes down to the metal n rubbing ....always thinking outside the box :rolleyes: Outside the box get it .....no........ I will get me coat ... :oops:

So to clarify the disc in the picture (provided it is not flipped) I would fit to the offside.

Why not try a "wanted" advert on here, and the other popular Land Rover forum is worth putting a "wanted" message on as well.

Sadly yes having looked at those pictures the chassis doesn't look good particularly at the rear.

Well aren't the slopes there for water displacement as well as heat dissipation? I would in that case follow the way car and motorcycle tyre tread considering they rotate in the same direction. So to the rear of the car would make sense to me...

Just a curveball ,Mabay the work is fine but the immobilizer has cut in ..Think it will turn over all day but wont start .. 🫣

That's what I did with mine - 2 zip ties. On a german Forum somebody helped me out with this useful tip: You can get the exact same connector from a 1999-2001 Jeep Grand Cherokee. They used it on the automatic gearbox wiring. Part number...

I'd look elsewhere, did I say that already 🤔

Think You can get lockers that are assessable above the wheel arches.

I’ve just got some more photos particularly of the underside. To my untrained eye it does look pretty bad under there, and probably worse than I expected after seeing the initial photos on the advert.

No it won't, the fuel cooler gets flow direcly from the bottom of the radiator, the return from the matrix goes into a T piece at the end of the cooler where it meets the outlet flow of the cooler when the thermostat in that piece is open cos...

I read it as they came down the section to the left of the waterfall going downhill, which is slightly less steep

Well now I’m confused. You are aware of the downhill VR but you didn’t drive the waterfall. Since there is no other way out I assume you turned round. Therefore doing most of the lane against the VR. That’s totally against the spirit of it...

Once you agitate the rubbers they come apart. The connections are tight

Im looking for a Discovery 2 TD5 with a 15P engine to use as spares for my Discovery im taking on a trip next year. The Discovery in my profile picture is the vehicle i need spares for is a pre facelift. Looking for a spares or repairs vehicle...

I think it's too rusty, by the time you have got rid of that rust, treated it, painted it, you will hate the sight of it. Remember chassis is always worse on the inside than the outside and it's hard work to do anything with it. It it's local...

I’m not concerned about the security side of things. We live down in Cornwall and I haven’t locked the car since we’ve head it, usually leave it open with the windows open and doors unlocked in car parks, gracefully it’s just not an issue down...