Latest activity

Thank you. Should the yolk be loose on the shaft.

What year is yours? My 1990 Ninety doe's not have any numbers on it. Looking at your pic can not be 100% but recon your axle is a Ninety unit. If you remove the top swivel and find it fits into a Railko bush then that confirms. Have a look at...

It’s so when the nick your doors at the next landrover show,you can go back to the campsite for spares

A folding rear step should fit with the towing plate.

Indeed. Vented, slotted and drilled discs are to be tried out. Will report back.

Hi, Manual car ? According to the manual the car need to be still, push the clutch pedal all way down, wait a little and then put the reverse. If you can’t get it to reverse, you certainly have issue with clutch hydrolics. Why I say that...

"This" was the first word if I remember correctly. Anyway, have you swapped the diffs yet?

Mine packed up Monday, was indeed a pain in the arse not helped by being supplied the wrong replacement (wrong plug fitting) at first, so had to exchange that. Then that one was a pig to get the 3 bolts to line up, which they eventually did, only...

Agree with the above, it may well have seating for four in the back but only if those seated on one side have legs. If you are a youngster I would strongly suggest an insurance quote would be wise, infact regardless of age get a qoute first.

I was not offended by one word, I was offended by a whole series of attacks over several days by many people. The point was that the belittling started from the very beginning from the very first word. If that word had been the only thing that...

And try washers and lock washers.

Trubble is doing that is far more complex than doing it with electricity, and as we now know they cannot even do that very well, hence huge windfarms being paid to not generate leccy whenever they can.

Did a little experiment, bypassed the heater matrix and now i have cool air coming from both sides. Still think ita not great but there is definitely a problem under the dash. Question is: is it easy to fix whatever is wrong or is it better to...

R U sure you mean that? A right-handed nut would need to be on a pulley that turns anti-clockwise to tighten itself. This is why peeps who have knock-ons have the nuts that tell you which side to put them on. There was once a member of a kit...

Never sure why anyone thinks turning a car body into a trailer is a good idea.

The shuttle vavle came off and is now in bits, being cleaned up for reassembly. The plastic switch seems to be fouling the shuttle valve itself if fully screwed down. No washer was there so head scratching time for assembly to make it work...

Hi There . Thank you for the idea but after looking into it it seems the crankshaft position sensor is more likely to cause starting problems . I have been scrambling all over the car looking for this sensor and so far I can't find it . Any...

Not sure but you’d get a very tight hub nut 😀

Need a photo of these wirings please?

Most of rot was caused by damage to outer cill but they all suffer at ends of cill all the bits behind plastic that catch mud, I suppose the answer might be to treat all these areas, structurally only removing lip of cill so not an issue also...

I do not… can’t find it

As you cured it for a few hundred miles maybe the pads are just not working well with the discs.

Yes 🤨

noted... will check. Good one to have. i think what i have is best described as a knocking sound no? All, another idea to get the crankshaft to go operating rpms. Would an impact drill with an appropriate bit get it to spin over fast enough to...

We were talking about this on one of the forums the other day. Helpfully, youtube just served this up to me. It is on thaor engined Disco, but the P38 is essentially the same I think. Somewhere in the comments a chap with a P38 has made the...

It is not an 89 truck. Many features mark it as noted above as a 300tdi. If Vin and V5 say so very likely it's a ringer.

Thank you all for your advice. The MOT history shows no advisories for any rust, although I'm not sure how much that can be trusted, as I'm aware of at least one other Landy nearby being an absolute bucket but having 0 advisories due to a dodgy...

Today's gripe. The alternator spat it's pulley oft again.. How can a right handed nut that secures a pulley that runs clockwise undo itself?!