Latest activity

Mine will do seventy quite quick for two bricks mating, bits threaten to fall oft thereafter..

Relay error as well swapped with another and system behaving at the moment, any idea on relay part number as not at home

Must be redders in the Hague, did you see the Trumpkins tan?!

The bearing press kit for the front main ball joints top and bottom had a perfect fitting sleeve + a dump hammer which I used

Well I'm not quite sure exactly what the issue was but touch wood I've fixed it! Got her running again this afternoon after giving the float bowls another clean out, checking the float level and blowing out the needle valve. Then replacing the...

Well I am pleased some of my advice was useful to you. Out of interest what did you use to knock the new seal in.

Was that on a recovery lorry? ;)

I have just got my new nanocom - still learning how to use it. Here are the error codes; injector 1 open load circuit detected - and then the same for the other 4 injectors. I then used the test function; Fuel Pump - push test button and it...

I have recently been given a 1997 discovery 1 300tdi that is too good to scrap. It has failed its mot on rear fog lamps. There seem to be red lights in the bumper and the bottom of the light cluster.Are these both fog lamps. The switch on the...

Thought I'd share this with you all. Scan of a cartoon from my fav cartoonist (GILES) from my collection, and a photo I took in 2022 when there for my dottir's wedding. Her married name is Giles. With a bit of foresight I should have put my...

That's the way to do it.

Old thread, but experiencing exactly the same issue so would love to know if you found a solution to the issue. Thanks!

Provided you are competent (knowledge + experience) you can do your own work. There are some jobs you are not supposed to do yourself, and require a proper electrician, such as installing a complete new circuit from the consumer unit, working on...

Result 👍 nice to know for my clients and their tratters👌

That's good work @uytter . Well done. This is all from your photos so I'm not 100% on any of this advice but..... The valve looks like an on-off switch. An electrical isolation valve, if you wish. Keep the positive terminal of the battery set...

Thanks What sort of diagnostics computer does someone need Or is best take it to a landrover specialist Probably cheaper than keeping swapping bits

Ok thank you 👍 forgive my ignorance but can anyone help me with a link to a new connector? Done some googling and am none the wiser 😅

Hi Anaconda Thank you for suggesting to use a NAK driveshaft seal fitted one today and the problem is now solved!!! What a relief the NAK seal is a lot tighter to fit and also tighter on the shaft don't use OEM or genuine they're crap! As I found...

Is that you at Gretna for a special event?? 😵‍💫

Hi Andy Thank you for suggesting to use a NAK driveshaft seal fitted one today and the problem is now solved!!! What a relief the NAK seal is a lot tighter to fit and also tighter on the shaft don't use OEM or genuine they're crap! As I found out...

You could de-pin the connector & solder a new wire between the contact & loom wire. Otherwise just replace the connector. That part of the loom usually has enough slack to reach.

Hi all- went to fit the new air intake temperature sensor (the one at the front of the engine next to the intake) and discovered that one of the wires to it is broken (see pic). I’m positive I didn’t do this as I was very careful getting the plug...

Its the death of the householder that electrocuted himself by feeding one room from two sources and only switchin one source off at the board.

You can do your own installation and get it certified by a registered a sparkey or get it registered under competent person act

I replaced that seat mesh on my trike. :) Seems OK. Time will tell. Is already nicer to sit on. Will need tightening up after a while.

Looked through the pics on my phone and found only one and that's not the best but you can just see the carpet on the kick panel and a bit of carpet showing on the passenger side too.

I felt embarrassed when I typed it 😉

I stuck black camping closed cell foam to mine then carpet to that. The other bits, I call kick panels if we are talking about the same things, to the right of the accelerater pedal? I stuck carpet to those aswell, I finished off that carpet...

Welcome to LZ.. Plug in your code reader, if you do not have one then if you are keeping the car you really really need a code reader.