disco300tdi
New Member
- Posts
- 59
- Location
- herefordshire
hi guys just a quick one i have a 32mm spanner to remove fan nut left hand thread how do you stop it turning so i can put pressure on the nut to release it many thanks oh its a 300 tdi m reg
viscous fan
- Thread starter disco300tdi
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
ssmn1234
Active Member
- Posts
- 691
- Location
- Cairns, Australia.
get yourself a strap wrench or a chain wrench to grip the pully.
Strap type is better as it wont mark pully. But you can use chain type just keep gradually adjusting it until it just grips, because if you apply too much pressure it'll bite into pully. Or you can get the correct special skinny open end **** spanner which may or maynot hold it without stripping the nut.
- Posts
- 67,744
- Location
- halfway between here and there.
just put the spanner on the nut and hit it sharply,this may well be enough to shock it undone.
disco300tdi
New Member
- Posts
- 59
- Location
- herefordshire
when i put the spanner on the nut just spins but i cant see anything else spinning
nathan5346
Well-Known Member
- Posts
- 11,939
- Location
- oldbury
shock it... short sharp whacks wi the ommer
- Posts
- 67,744
- Location
- halfway between here and there.
it is a fine thread,you sure it is not undone already.just try undoing it by hand.
ssmn1234
Active Member
- Posts
- 691
- Location
- Cairns, Australia.
"Wack it"
well if you must, just be aware that the wack is gonna transfer energy into water pump bearing??
well if you must, just be aware that the wack is gonna transfer energy into water pump bearing??
nathan5346
Well-Known Member
- Posts
- 11,939
- Location
- oldbury
never had problems wi getting mine off using the short sharp shock method
ssmn1234
Active Member
- Posts
- 691
- Location
- Cairns, Australia.
Maybe so, but strap wrench cost bugger all compared to the possible risks involved with the wack method.
nathan5346
Well-Known Member
- Posts
- 11,939
- Location
- oldbury
if the shock method dont work without getting the sledge hammer out then obviously yes there are other methods
nathan5346
Well-Known Member
- Posts
- 11,939
- Location
- oldbury
u sold ya rangie yet john?
lerk
New Member
- Posts
- 1,763
- Location
- Creswell, Derbyshire UK
"Wack it"
Err... not really as that's 2 foot away from the fan! :doh:
disco300tdi
New Member
- Posts
- 59
- Location
- herefordshire
quick update just gave it a "tap" with the hammer and hey presto off it came thanks for all your help
nathan5346
Well-Known Member
- Posts
- 11,939
- Location
- oldbury
u didnt need the aussie strap then?
disco300tdi
New Member
- Posts
- 59
- Location
- herefordshire
lol no not this time maybe another day
- Posts
- 67,744
- Location
- halfway between here and there.
u didnt need the aussie strap then?
bloody hell,that sounds like a torture implement nath.
- Posts
- 67,744
- Location
- halfway between here and there.
quick update just gave it a "tap" with the hammer and hey presto off it came thanks for all your help
tis easy when you know how isn't it.just like most things though.
- Posts
- 67,744
- Location
- halfway between here and there.
no not yet nath,i have not tried yet,still undecided what to do,keep it or flog it.
decisions decisions.ssmn1234
Active Member
- Posts
- 691
- Location
- Cairns, Australia.
2 foot?? 300tdi must be configured differently over here then.
ssmn1234
Active Member
- Posts
- 691
- Location
- Cairns, Australia.
quick update just gave it a "tap" with the hammer and hey presto off it came thanks for all your help
u didnt need the aussie strap then?
I am glad it came off so easy. "One tap" just the one? I suggest it has been removed before then, and threadlocker not reapplied as in the original fitment.
It's your Motor you treat it as you wish, I woul rather do it with a strap wrench in the knowledge that unnecessary force has not been applied to the waterpump components.:doh:
