hughesy
Well-Known Member
- Posts
- 4,200
- Location
- Isle of Anglesey
I must be doing something wrong. I've had four 200tdi discos over the years and okay there's been some rust but none of em have ever broke down on me.
Last edited:
Torch the f****r
- Thread starter philbr
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
ssmn1234
Active Member
- Posts
- 691
- Location
- Cairns, Australia.
Sure can, but you'll need some very clean lint free cloth to stuff in both front and back of hub to keep the grunge out, or you'll be replacing seals and bearings, which probably would be a good idea to replace anyway by the sounds of other things breaking. Possibly need about 6 more beers to do it though.
ur 300tdi was so good u bort a td5?
Yes, the TD5 is a bit more refined engine wise and thus quieter. The 300 pulls well but is damn noisey doing it. I also believe the TD5 is more tuneable power wise.
pete5570
New Member
- Posts
- 180
- Location
- North East
I'e had my disco for 6 months now and it has been great, i've done about 5k in it with no probs. After reading this though i think i might go and give the underside a coat of looking at!
string
Member
- Posts
- 88
- Location
- Beckenham, Kent. England
I've had my '93 200TDI for about 5 years in which time I've had the alternator fail, 3rd gear synchro fail both within the 1st week, dealer replaced free of charge. Then head gasket blow, garage job including skimmimg. 1st MOT failed due to badly worn front tyres, tracking out had to have all the rods heated up to adjust the tracking. Next MOT full set of discs and pads, both headlights. Mother rust has taken it's toll and that has to be done before January or will fail the MOT work to do, Load space floor really knackered who knows what the rear panel is like under the bumper, offside inner wing perforated, MOT guy said because the brake pipes are fitted to them it's a fail. Offside body mounting attached to the sill a touch swollen apparently that's a fail to. Glad I took the side steps off they were so rotten standing on them was risky, probably would have passed the MOT though.
The rust alone is enough to chuck it but she drives so well, never had a breakdown. Been in the sea and river pulling boat trailers out, dragged sunken caravans out of the mud even pulled a japanese copy along in the snow and ice. These are the only reasons I'm going to fix her up.
The rust alone is enough to chuck it but she drives so well, never had a breakdown. Been in the sea and river pulling boat trailers out, dragged sunken caravans out of the mud even pulled a japanese copy along in the snow and ice. These are the only reasons I'm going to fix her up.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
That might explain the rust then Salt water and steel don't really like each other very much.
string
Member
- Posts
- 88
- Location
- Beckenham, Kent. England
I agree salt's not good, when I bought her the first job was to clean the underside which was caked in 10 years of mud. My guess is that's what caused the rust damage along with winter road salt especially as the rear spashguards fell off with the mud and the drivers side inner wing parted allowing water to be thrown up all over the battery every time it rains. The load space floor was different as there was no damage to the underside, it rotted away from the inside where rain water crept in through the roof lights. Anyone know how to fix these the water even finds it way into the roof liner and drips on your head?
Since getting the mud off I've managed to keep on top of the rot by jet washing every time she goes into the sea/river and a couple of time during the winter to get the road salt off. Once the rot has started it's just a mater of time before the decsion to spend or torch reaches them all.
Nick Santon
New Member
- Posts
- 6
At least you can mend it. They are the most unreliable things ever made but I do love mine. Series 2 have got the added fun of loads of well dodgy electronics which play up in the wet and air suspension which is fine but costs a mint to fix.
- Posts
- 67,763
- Location
- halfway between here and there.
i replaced the boot floor in a discovery im repairing and the lip the boot floor fits into was rotten so i went to a local metal fabricator with a press and had some 'lips' fabricated. i cut out all the rot right back to good metal then welded the parts in then dropped the boot floor in. i was extreamly please with the results
nice and neat work viv,well done bud.
PASTMASTER
Well-Known Member
- Posts
- 1,235
- Location
- S London
Letsgodisco
New Member
- Posts
- 35
- Location
- S.Yorkshire
I fancy trying the "creeping crack cure" on my new one. Problem is people say it has to be dry.
Can someone remind me to do it in the summer!
P.S. Will it creep down under the bonnet, and fix a cracked head???
Can someone remind me to do it in the summer!
P.S. Will it creep down under the bonnet, and fix a cracked head???
iannotts
New Member
- Posts
- 4,401
- Location
- East midlands,
Similar threads
