discomania
Well-Known Member
- Posts
- 6,949
Will a TD5 finisher fit on an earlier 90?
I assume they are identical except for the little vents.
I assume they are identical except for the little vents.
TD5 headlight finisher
- Thread starter discomania
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
ratty
I'm not special I'm limited edition
- Posts
- 34,277
YES. I fitted a set to my old 1990 v8 110.
discomania
Well-Known Member
- Posts
- 6,949
Excellent - I will get some next time I am ordering parts.
Griffdowg
New Member
- Posts
- 7,194
- Location
- Somewhere in Bristol
How easy are they to fit? the sidelights are no prob. but will i have to remove the headlight bowl to fit? mine have faded bad. new ones on paddocks are reasonable but i dont want to fiddle too much before going away.
G
G
bustersbus
Well-Known Member
- Posts
- 13,755
- Location
- Near Dumfries, Scotland
Griffdowg
New Member
- Posts
- 7,194
- Location
- Somewhere in Bristol
i did think of that. but sometimes my spraying is hit n miss! the wolfs turned out good, but my new load rack in the back (cut and welded by me 
1st time welding - very proud) sprayed grey isnt as good!
I suppose for the money you are right buster
so do they come off with the removal of the sidelights and the 3-4 screws holding them in?
1st time welding - very proud) sprayed grey isnt as good!I suppose for the money you are right buster
so do they come off with the removal of the sidelights and the 3-4 screws holding them in?
bustersbus
Well-Known Member
- Posts
- 13,755
- Location
- Near Dumfries, Scotland
Just unscrew the side lights and take them off, then (if like mine) there's only two other screws to take off, dead easyi did think of that. but sometimes my spraying is hit n miss! the wolfs turned out good, but my new load rack in the back (cut and welded by me
I suppose for the money you are right buster
so do they come off with the removal of the sidelights and the 3-4 screws holding them in?
Here's a piccy ...
Ah did mine when they started to fade a bit, and also the grille so it all matched
Griffdowg
New Member
- Posts
- 7,194
- Location
- Somewhere in Bristol
exc work buster. thanks for confirming the non removal of the headlight! will take it all off tomorrow, spray up and refit on wednesday. all ready for the off on Saturday was thinking of going grey though
G
will take it all off tomorrow, spray up and refit on wednesday. all ready for the off on Saturday was thinking of going grey though G
bustersbus
Well-Known Member
- Posts
- 13,755
- Location
- Near Dumfries, Scotland
Nae probs Griffexc work buster. thanks for confirming the non removal of the headlight!
G
Just remember what wires go where... unless ye've got them new fangled plug things
Griffdowg
New Member
- Posts
- 7,194
- Location
- Somewhere in Bristol
300 mate plugs all around, easy peasy. just got to decide on colour now! was thinknig dark grey. but i have black and light grey here. decisions decisions!
plugs all around, easy peasy. just got to decide on colour now! was thinknig dark grey. but i have black and light grey here. decisions decisions!
ratty
I'm not special I'm limited edition
- Posts
- 34,277
If yours have faded griffy, either run a heat gun/hair dryer over em or wipe some back to black over em.
bustersbus
Well-Known Member
- Posts
- 13,755
- Location
- Near Dumfries, Scotland
Just a thought... won't the dark grey look like faded black? Ah'm sure ah seen some light grey/ aluminium coulored ones somewheres... LRX or summit like that??300 mate
Griffdowg
New Member
- Posts
- 7,194
- Location
- Somewhere in Bristol
well mine were just patchy got them all off, sanded and sprayed in 30min!
will fit them later if they are dry. went for black in the end
Cheers Buster
G
got them all off, sanded and sprayed in 30min!will fit them later if they are dry. went for black in the end
Cheers Buster
G
