Steve's Land Raft

Dauphproto said:

While on that subject, my pickup has no back door just the tailboard, where is the wiring hiding for washers, wiper and heated screen??? There are a couple of plugs on the harness where it crosses the rear cross member. What are these? Oh and is the Genuine 300 TDI manual worth the money. I find Haynes manuals a waste of time since the late 80's

Click to expand...

The wiring should all be in the drivers side corner behind the ali light panel. There are two plugs one for heated screen and one for wiper motor. i don't have a picture to hand but if you upload a picture of the rear loom behind that panel it should be fairly obvious which ones are which. Also I am not sure one the plugs on the rear cross member again may need a picture to identify. when I was rebuilding mine I found LRWorkshop to be invaluable for identifying wiring colours and connectors (LINK)

On manuals I would suggest the genuine manual is possible worth having but I wouldn't spend much money on it. I use my parts manual all the time but find google and a reputable forum like this (plenty of unreputable ones) is easier and better than the manual. I have one for mine on the shelf that is rarely used whereas the internet and on here is my go to for nearly everything.

Dauphproto said:

I had been looking at them for a door and a Bulkhead.
Just to check I'll need a door, hinges, a latch & keeper. Oh and a seal .
Anything else?????

Click to expand...

Door card ... I like the one from Mud.

Dauphproto said:

<snip> is the Genuine 300 TDI manual worth the money. I find Haynes manuals a waste of time since the late 80's

Click to expand...

dag019 said:

On manuals I would suggest the genuine manual is possible worth having but I wouldn't spend much money on it. I use my parts manual all the time but find google and a reputable forum like this (plenty of unreputable ones) is easier and better than the manual. I have one for mine on the shelf that is rarely used whereas the internet and on here is my go to for nearly everything.

Click to expand...

Yes, I second that, if you get really stuck you can RTFM, but there are some good knowledgeable folk on here.

miktdish said:

Door card ... I like the one from Mud.

Click to expand...

Your choice of door card depends on what you expect to be using the vehicle for. The genuine one is terrible and is basically a piece of cardboard, I also like the look of the MUD one but I have a price of black chequer plate as my door card because I regularly have large heavy things in the back of it and didn't want to risk damaging a plastic one.

I hadn't thought about the inside of the door. Was trying to get it fitted wind and watertight. Would be nice to have an alloy outer skin from an originality point of view, but the completely Galv frame and plated galv skin will be stronger and less prone to corrosion, so is looking like a winner. Do you just put the door in the hole and drill the middle and lower hinge holes, are there reinforcing plates to fit???

Dauphproto said:

I hadn't thought about the inside of the door. Was trying to get it fitted wind and watertight. Would be nice to have an alloy outer skin from an originality point of view, but the completely Galv frame and plated galv skin will be stronger and less prone to corrosion, so is looking like a winner. Do you just put the door in the hole and drill the middle and lower hinge holes, are there reinforcing plates to fit???

Click to expand...

I am in the same position. I would ideally want a galv frame with alloy skin. But all galv is looking like the front runner for me as well.
What do you mean about drilling holes? Which holes do you not have?

dag019 said:

I am in the same position. I would ideally want a galv frame with alloy skin. But all galv is looking like the front runner for me as well.
What do you mean about drilling holes? Which holes do you not have?

Click to expand...

As it's a pickup with a tailboard there are no middle or lower hinge holes in the tub rear. Do the Bolts holding theTailboard hinge keeper fit the bottom hinge for the middle hinge there is a reinforcing plate, but mine has 1 big hole with an anti-luce pin in it which will need removing.
Common sense tells me that if i get the top and bottom fitted and working then the middle will sort itself out an obviously I can make spreader plates for inside the rear tub if I need to. This is my First Landy pick up to hard top conversion, so once it's done I'll know how to do it .................properly....maybe.

Dauphproto said:

As it's a pickup with a tailboard there are no middle or lower hinge holes in the tub rear. Do the Bolts holding theTailboard hinge keeper fit the bottom hinge for the middle hinge there is a reinforcing plate, but mine has 1 big hole with an anti-luce pin in it which will need removing.
Common sense tells me that if i get the top and bottom fitted and working then the middle will sort itself out an obviously I can make spreader plates for inside the rear tub if I need to. This is my First Landy pick up to hard top conversion, so once it's done I'll know how to do it .................properly....maybe.

Click to expand...

when I went the other way on my series to fit a soft top, removing the door and fitting a tailgate I replaced the whole triangular capping piece as this is just riveted on. If you can get hold of one of those that already has the holes drilled into it is might be worth swapping over. As then you have two hinges lined up correctly and attached so the bottom one will be easy to drill in The correct place.