Evening people. This is my first post on here , but sure it wont be my last. My miss's has a RR vogue 3.0 diesel 2005. It's got the bmw m57 engine. A few months ago we had the misfortune of our first major breakdown. Snapped aux belt. Loss of coolant major problems got it recovered to a garage friend of a friend. To look at and fix. Unfortunately he went ahead and fixed it and slapped a £1200 bill on my miss's. After alot of swearing the bill was payed. Upon return the car was losing coolant. Suspected head gasket it went back to be diagnosed/rectified. A bit of luck it was a split coolant pipe. Bad news no longer available. And to top it off , over night has shat all its brake fluid from brake pipes. We have now had it brought home. And I'm going to do the work on it for her to keep cost down as she cant put anymore money into it. As I've never done any work on this car I'm a novice so I'm asking for some help and advice from you lot. What's involved in rear drivers side brake line removal. And the coolant pipe is egr cooler. Can I remove the egr cooler and delete egr valve with out any problems to car? Thank you for reading sorry it's so long I promise the next ones will be shorter.
Range rover nightmare.
- Thread starter f40cab
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Datatek
Well-Known Member
- Posts
- 43,931
- Location
- Near Poitiers SW France
You should be able to find the coolant hose, try Island 4 x 4 or Rimmer Bros. Deleting the EGR valve is technically an MOT fail and it's not that simple as the engine ECU would need to be remapped to eliminate it.
Brake pipes rusting through is a common problem. Replace with CUNIC, you can buy a flaring tool on line for making the joints. Not a difficult job if you have a pit or a lift, a PITA laying on your back.
Welcome to the mad house, good luck trying to sort it.
I am afraid its probably not worth your time 
BUT if you are willing to spend knuckle skin and filling a swear jar, we will help.
Oh is it a RR sport?
I don't believe the "no longer available"
Oh "overnight it shat its brake fluid"
Fishey
We all appreciate an introduction post.
J
BUT if you are willing to spend knuckle skin and filling a swear jar, we will help.
Oh is it a RR sport?
I don't believe the "no longer available"
Oh "overnight it shat its brake fluid"
Fishey
We all appreciate an introduction post.
J
Datatek
Well-Known Member
- Posts
- 43,931
- Location
- Near Poitiers SW France
L322 M57 2005 according to the OP.I am afraid its probably not worth your time
BUT if you are willing to spend knuckle skin and filling a swear jar, we will help.
Oh is it a RR sport?
I don't believe the "no longer available"
Oh "overnight it shat its brake fluid"
Fishey
We all appreciate an introduction post.
J
thanks for response , I know its mot no no, but under engine covers so they cant tell. And I.dont think its eletronic so dont think it will show any lights, but I might be wrong. As for brakes I've got all hydraulic flaring tool and pipes in garage done lines on other cars before. Unfortunately no ramps so will be crawling around like a slug on floor.lol what's best way to jack up car with out damaging air bags. And do the lines run down passenger side then over rear axel at the back. Or do they run down both sides.
Datatek
Well-Known Member
- Posts
- 43,931
- Location
- Near Poitiers SW France
Jacking up the car should not cause a problem, buy some ramps? If no ramps make sure you use axle stands.
The EGR is electronically controlled with feedback as far as I know so removal will flag errors. With the latest MOT over here they can tell is there has been a delete.
Hippo
Lord Hippo
- Posts
- 51,876
Make yerself some HippoRamps (tm)
www.landyzone.co.uk
HippoRamps - How To Guide
Updated 29 July 2015. This write up shows the design and measurements used to make my HippoRamps. The original ramp section was shorter. This guide shows the betterer longer design with a shallower slope. It was a bit hit and miss driving up the ramps if the tyres were damp on the original...
www.landyzone.co.uk
Hello, mine, same age and model failed on brake pipes all round last year, yes they do run down the passenger side then over the rear axel. I did it without ramps, not too bad a job but you do need to do a lot of crawling about under the rear axel. The ends of the rear pipes are flexi with steel bits in the middle, on mine it was the steel bits on the flexi that the tester took objection too, worth a look before you start in case you need to replace them. On inspection the pipes over the axel weren't great so I replaced the lot. The font ones are a PITA you have to remove the plastic arch liners and I snapped a height sensor cable wrestling them off which went unnoticed until I put it all back together.
Hope that helps
Hope that helps
As for the pipe I've give the part number on pipe to landrover and its discontinued. Then tried bmw and they also said it's been discontinued. Possible get a second hand one if I ring round it's more now the brake line repair. I can see it being a big job due to corrosion and in experience. Lol. But I'm use to working on fords so I'm use to rust now.
- Posts
- 6,025
- Location
- uk
Try searching on this useful website, sign up for a wider search.
It will also give other links for the part you are searching for.
It will also give other links for the part you are searching for.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,263
- Location
- Trapped inside my head @ LZ asylum
There’s a search function in top right corner looks like a magnifying glass, there’s loads of threads about people making new brake lines.
£1200 seems a lot. I wouldn’t be happy with that.
£1200 seems a lot. I wouldn’t be happy with that.
- Posts
- 18,961
- Location
- Buckinghamshire, UK. ('95 DT)
Got to your local motor factors and get cupronickel pipe. Don't get it off the internet unless it is a trusted supplier as there is a lot of fake stuff out there. It is flexible enough that you can just bend it to shape. A small pipe bending tools will be required for tight bends. Flaring tool is cheap enough off eBay.
rich28uk
Well-Known Member
- Posts
- 625
- Location
- Manchester
Go ahead with a egr delete kit that also bypasses the cooler, this should help there. Don’t worry about warning lights as on the m57 of that age there vacuum operated not electric, it does have a fault code for egr vacuum if you hook up a scanner but it doesn’t bring a warning light on (previous experience with my own td6 and x5 before it)
Check all brake pipes as they do rot on Rangies, once sorted cover in grease and should last the life of the car, other than weak gearboxes there a good car.
Check all brake pipes as they do rot on Rangies, once sorted cover in grease and should last the life of the car, other than weak gearboxes there a good car.
Datatek
Well-Known Member
- Posts
- 43,931
- Location
- Near Poitiers SW France
No need for grease on cupronickel pipe.
They have started plugging in to the OBD port on the MOT here so can spot if the vehicle does not conform.
rich28uk
Well-Known Member
- Posts
- 625
- Location
- Manchester
Depends on where the OP is based. It’s not something done in U.K., just a visual check to see if any warning lamps are on and even then it’s not all of them, think it’s engine, brakes etc. important stuff.
Datatek
Well-Known Member
- Posts
- 43,931
- Location
- Near Poitiers SW France
As the UK does not have to follow EU MOT rules post BREXIT, it is to be hoped that things stay that way
Ye that's kind of what I was thinking regards egr. Looking at corrosion on brake parts think this could be a full brake strip down calipers flexi solid lines. Not sure the calipers will bleed up with the old rusty nipples. I need to get underneath after xmas. Thank you again for all the help and advice. Cars been ok so.far few bits electrics but easy fix's.
Similar threads
Freelander 2 (LR2)
Turbo coolant return pipe
Freelander 2 (LR2)
Looking for a second market EGR Cooler for
