Series 3 Gearshift Jammed in Neutral on S3

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Moorhouse2

Moorhouse2

Member
Posts
62
Location
Northumberland
Before I start pulling things to bits I thought I would glean some insight from others who are likely to have better ideas/experience. I have S3 diesel 1982 (all standard), pretty reliable, no previous gearbox or clutch issues, strange noises etc. Reversed out of shed this morning, no problem engaging reverse gear, then went into first no problem to go a few feet forward to get a better angle past a parked car, but really struggled to get out of first back into neutral and then couldn't get back into reverse at all. Gear lever will not move fore and aft at all with only a little sideways movement from neutral position. It's really solid and no hint of movement even with a fair bit of force and with clutch depressed- same with engine running or not. No clunks or strange noises during entire sequence. Gearlever will move up and down on the spring as it does when you go to engage reverse but won't go completely to the left or fore and aft. Plenty of clutch fluid and no signs of a leak from around the slave cylinder although the clutch pedal does seem slightly lighter than normal. Any suggestions gratefully received - I'm guessing either slave cylinder (although would expect at least some ability to go into gear) or, more likely, selector mechanism issue in top of gearbox. I have tried a search on the forum bit struggling to find anything relevant so any pointers would be great before I start unscrewing things to have a look. Many thanks........Ian (currently regretting fitting copious amounts of Killmat sound deadening and rubber matting to entire cab floor over gearbox access panels!!)
 
Clutch pedal lighter suggests an issue with it. Possible fail of master cylinder seal [ black in reservoir a sign] However one should still be able to select a gear or two with engine off.
Have known a stone to fall in just the right position to jam selectors and end of stick to break.
 
I've had a broken synchro spring give me grief like this, but lots of wiggling of the lever let it fall free. I didn't know what caused it at the time, but all became clear on the next oil change.
 
Judging from the killermat, check if you have plenty of clearance under the pedal. Maybe you fitted some and now you cannot fully engage it properly? Still wouldnt explain the weird "lockup".

with aftermarket selectors, the O-ring at the end of the selector is different and can therefore sometimes slip between the gear forks. this will give you a really loose gear shifter and you wont be able to engage anything. But this also doesnt seem to be the case.

As mentioned before, probably just check ur slave and master. Possibly only replacing the slave? but if the slave failed, the master cant be far behind.
 
Thanks for the replies so far - haven't had time to get at it just yet but some good ideas of what to check for. Just before I dive in, can someone just confirm that on a normal S3 you should be able to get into at least a couple of the gears from neutral even if the clutch is engaged (ie pedal up with engine off). On all of my other old stuff its possible, although a bit baulky. Just trying to rule clutch out of the equation before I start taking floor up. Could start with clutch slave/master cylinder I guess but sneaky feeling its more than that.
 
Yes one can usually find a gear or two with clutch out, engine off and at a stand still but given your stick will only move a small amount I guess other issues as noted in posts above.
First thing out with floors and tunnel to view selectors on the top of the box.
Britannica restorations and or Steamwally for videos of what you will be looking at.
 
Just a quick update for anyone interested - turned out to be a straightforward fix. Removed transmission cover and discovered the 1st/2nd gear selector shaft had either not slid all the way back or had moved slightly forward and the ball on the end of the gearlever was effectively trapped in the "socket" end of the 3rd/4th selector shaft. Hence the limited movement in both directions, any sideways movement blocked by the socket end of the 1st/2nd selector shaft. Pushed the selector shaft back manually with a pry bar and hey presto, all gears now available and working fine. Bit of a road test and all still seems fine but plan is to leave transmission cover off for now just to see if it happens again. Not sure why the selector shaft wouldn't have come all the way back or moved forward a smidge but we'll see if it re-occurs. Thanks to everyone who gave advice and hints - much appreciated. Note to anyone applying the self adhesive sound deadening products like Killmat or Dodo Mat to the floors - take the time to leave the screw and bolt heads and the overlapping edges of the floor panels uncovered or cut out - don't be an a*s like me and just slap it on over everything 'cos its a pain to get off once it stuck down! Thanks again....Ian
 
Good to have an update.
It could be that the pinch bolt that holds the selector fork has come a bit loose. It would not be able to move much but perhaps just enough.
To check remove gear box top. First remove the plates that hold detent springs each side of box top and the cap on top that holds detent on center shaft.
Lift of top being careful to note the detent balls, remove and keep safe while checking shaft. Come back for more info if needed.
 
boguing said:
I wouldn't drive it with the cover off! Not unless you like the taste of gear oil.
Click to expand...
Yes, probably should have said the gearbox tunnel panel to be fair so not the actual gearbox itself, although being farmers we are used to the taste of superheated hydraulic fluid as it hits you in the face from burst trailer couplings, drive pipes etc. Plus a quick sandwich on the go in the middle of harvest is not complete without some oily fingermarks.

I'll check out the pinch bolts as suggested before I put everything back together.
Thanks..Ian
 
Sounds like you've been there as well. Was worse back in the day when the back window was always open as you had no A/C - massive grab to pull the window down as 15 tonnes of corn pushes the ram back down and hydraulic oil hits the windscreen from the inside. Easier now with all the controls inside the cab, positive pressure cabs and A/C. Hydraulic unions all still leak for a pastime though hence the oily sandwich!
 
You must log in or register to reply here.

Similar threads

M
Land rover series 3 clutch/gearbox issue, I just can't get it in gear
Replies
7
Views
2K
tottot
tottot
G
Land Rover 300tdi clutch not disengaging after engine out
Replies
8
Views
2K
miktdish
miktdish
Cornishdefender
Clutch pedal travel suddenly changed - now bite point in last 2 inches towards floor
Replies
4
Views
449
Cornishdefender
Cornishdefender
N
Clutch problem unable to change gear
Replies
10
Views
623
Anaconda
A
htr
Freelander 1 Drain the gearbox?
Replies
2
Views
239
Arctic2
Arctic2
Back
Top