Fitting the Nakatanenga Snorkel to 300tdi Defender

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.

gymmaniac

Well-Known Member
Posts
621
Location
Bedfordshire
A few posts to follow with how over the last couple of weeks I've spent all the fuel money I've not used on too many wrong sized bits of kit and how I eventually got everything connected.
 
Last edited:
So the Nakatanenga snorkel came from 4x4overlander pretty damn quick. Nicely packaged.

snorkel1.jpg snorkel2.jpg
The only think I didn't like is that the welding wasn't complete all the way round the wing-top plate:
snorkel3.jpg
 
I started buying all the pipework to connect the snorkel but have had it in my mind for a while now to get rid of the standard air filter; thus the project expanded a little to get a full set of new pipes between turbo and snorkel.

Matching the various IDs and ODs to make everything fit was a mission (final parts list to follow). Also Steel pipes are heavy! They got changed to Ali. I did find on the trial fit that the pipes I'd bought were too big to get around the back of the engine so had to start again on the hunt for parts (loads of spare 100 and 80mm silicon hoses now.....)
 
oh yeah, I also worked out eventually that I can't just get rid of the oil catch pipe, well not without even more bits to try and fit, so that resulted in another rethink.....
 
So what I ended up with:

oil catcher pipe extended:
fitting1.jpg (It got shorted when in place to line up with the T)
Turbo pipe first section:
fitting2.jpg
Air filter section made up (even though had to remove input hose again as not enough room to get the corrugated snorkel hose to fit):
fitting3.jpg
I had to modify the bracket that will support the air filter:
fitting4.jpg
I could then line everything up and get everything fitting:
fitting5.jpg

Between the two 90degree bends is a 24cm length of 76mm OD ali pipe.
At the air filter side between the 90 and 45 degree bend is an 8cm length of 76mm OD ali pipe.
Between the snorkel corrugated pipe and filter reducer there is a 6cm length of 82.5mm OD ali pipe.

Also a whole shed load of jubilee clips!!
 
Result:
finished1.jpg finished2.jpg finished3.jpg result.jpg

Had a bit of trouble fitting the snorkel top as it was a bit big but padding it out with an end off one of the many spare hoses I've got it's now solid.

Should also say that she seems to breath a lot easier now and the turbo actually seems to kick in better. Do not disagree with this - I wasted a lot of money to believe it.
 
Last edited:
Parts list in case you'd like to add up how much it cost me (does not include the many sections of pipe and hoses that I didn't use!!!!).

Other sellers exist I'm sure this is purely for reference so you can get the right size parts if you want to do the same thing.


From top to turbo:
Snorkel top
https://www.ebay.co.uk/itm/A-Premiu...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649

Nakatanenga snorkel
https://www.4x4overlander.com/product/defender-rai-for-roll-cage/

82.5mm OD pipe
https://www.ebay.co.uk/itm/ALUMINIU...var=492470368820&_trksid=p2057872.m2749.l2649

Filter
https://www.ebay.co.uk/itm/K-N-54-5...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649

Filter bracket
https://www.ebay.co.uk/itm/K-N-Filt...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649

Filter bracket mounts
https://www.ebay.co.uk/itm/4x-LAND-...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649

45-degree bend 76 ID
https://www.ebay.co.uk/itm/Silicone...var=622227833360&_trksid=p2057872.m2749.l2649

90-degree bend 76 ID (short leg)
https://www.ebay.co.uk/itm/Silicone...var=622227849975&_trksid=p2057872.m2749.l2649

76mm OD pipe
https://www.ebay.co.uk/itm/ALUMINIU...var=492470368793&_trksid=p2057872.m2749.l2649

90-degree bend 76 ID (long leg)
https://www.ebay.co.uk/itm/Silicone...var=412653006432&_trksid=p2057872.m2749.l2649

Oil catcher adaptor 25-19mm
https://www.ebay.co.uk/itm/corrugat...var=512034000802&_trksid=p2057872.m2749.l2649

oil catcher pipe hose
https://www.ebay.co.uk/itm/Rubber-F...var=522648567968&_trksid=p2057872.m2749.l2649

Aluminium T-piece 76 and 25mm
https://www.ebay.co.uk/itm/Aluminiu...var=493237424805&_trksid=p2057872.m2749.l2649

Reducer 76-60mm ID
https://www.ebay.co.uk/itm/Silicone...var=412656057941&_trksid=p2057872.m2749.l2649
 
Back
Top