dti tool

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
paddocks1967 said:
hi lads,going back to the fuel injection pump,i now have the pump puller but i have read that i also need a dti tool to set the timing what is dti tool and where can i get it,cheers pat.
Click to expand...

You don't need the pump puller or more correctly pump pusher to do the timing. There was a thread about the adaptor from the states i got one off eBay £21.00 including post from California. Item 370483411322 eBay. You will then need a DTI. For about £20.00 almost anywhere. You will also need a TDC locking pin.

PS
Have just looked at item it appears they have sold out. But there are others in states but a little more expensive.
 
Last edited:
BladeRob said:
Sorry - missed that!
Click to expand...


The adaptor is made by JTC auto tools. It is for VW Bosch VE pumps but can be used for the BMW Bosch pumps. Look at eBay item 250780312796.
That is somewhat more expensive than the one Nathan found that is now sold out, but if you look on eBay the DTI can be got for around a tenner. So you can have what you need other than the locking pin that you also require for around £40.00.
 
Last edited:
Hi guy's thanks for the replies,wammers I have just bought a dti of eBay for £12,and injection timing tool from america,comes in about £30 so you spot on with your price,now just need to get lockin pin,do you know where to get one.cheers pat.
 
paddocks1967 said:
Hi guy's thanks for the replies,wammers I have just bought a dti of eBay for £12,and injection timing tool from america,comes in about £30 so you spot on with your price,now just need to get lockin pin,do you know where to get one.cheers pat.
Click to expand...


Have found mine that was lost. Will mike it up later and let you know dimensions.
 
Ok dimensions for LRT-12-108 are.
Length. ---------------------------130mm.
Major diameter.--------------------11.99mm.
Nose spigot. 10mm long. Diameter---7.89mm. With a slight lead chamfer.

So 12mm silver steel with 10mm nose turned to 7.90mm should do the trick.
 
Last edited:
paddocks1967 said:
hi wammers,you could'nt do my a favour and show me a picture of the locking tool,cheers pat.
Click to expand...

Hows this?

lrt-12-108.JPG
 
wammers said:
Ok dimensions for LRT-12-108 are.
Length. ---------------------------130mm.
Major diameter.--------------------11.99mm.
Nose spigot. 10mm long. Diameter---7.89mm. With a slight lead chamfer.

So 12mm silver steel with 10mm nose turned to 7.90mm should do the trick.
Click to expand...



What can I say Wammers.....other than Your a Star !!!!:praise::praise:
 
Irishrover said:
What can I say Wammers.....other than Your a Star !!!!:praise::praise:
Click to expand...





Us old buggers have our uses. As a matter of interest. Missus works on reception at hotel opposite Samlesbury. She has had a few blokes in for a long time. They are fitting some Makino automatics in two shed. They should have been finished at Christmas but are still there, held up by health and safety. They can't go for a **** without a risk assessment apparently. And we wonder why everything is made in India and China these days. Various governments, notably Thatchers, caused total mayhem getting rid of restrictive practices that slowed production. Rightly in some cases. Then introduce sometimes totally stupid health and safety regulations that made things ten times worse. You could not make it up. No wonder we are in the ****.
 
Last edited:
nice to see my investigation into a cheap way of setting up the pump has helped someone else! and that my figures for the locking pin werent to far out either!
just a point to add if you have hot start issues set the timing to 1mm instead of 0.9mm as stated in rave have done this twice now and has worked perfectly!
 
You must log in or register to reply here.

Similar threads

T
Classic VM Injection pump removal
Replies
5
Views
664
norseman
norseman
tweedandbriar
Td5 Injector Puller / Removal Tool
Replies
1
Views
623
Anaconda
A
Ric82
Series 3 2.25 Diesel Timing Tool 605863
Replies
3
Views
1K
Ric82
Ric82
D
L320 TDV8 Steering Angle Sensor (SAS) - repair??
Replies
0
Views
323
dunc101
D
J
TD4 crankshaft pulley.
Replies
2
Views
302
Jonny H
J
Back
Top