Disco rear seat project

took a step forward today, seat arrived from BLRS. Not bad, I only ordered
it on monday, and it's a non-standard line which they had to cover the
cushions specifically for, so they weren't on the shelf.


anyone with these 90/110 etc. rear benches know if there's supposed to be
anything holding the seat cushion on? doesn't appear to be on this'n. the
seat back part is obviously normally bolted down to the wheelbox and the
base part is hinged, and clearly rests on the wheelbox, overhanging it by a
few inches. The required frame looks dead simple in fact, just needs to
support the sides where the backrest part bolts on and have a support along
where the front edge of the wheelbox would be if it was on one. I reckon it
can all be done with 2 legs, given suitable bracing in the middle. The
backrest is apparently only supported at each end, although of course in the
original installation it can't move far without hitting the side of the
vehicle. I may decide on an additional frame member each side to add to the
support of the backrest part.

now to invent a method of holding it down securely while still being
removable without use of tools...

Austin Shackles vaguely muttered something like ...
> anyone with these 90/110 etc. rear benches know if there's supposed to be
> anything holding the seat cushion on?

Not as standard .. mate used sticky back velcro strips ..

> doesn't appear to be on this'n.
> the seat back part is obviously normally bolted down to the wheelbox and
> the base part is hinged, and clearly rests on the wheelbox, overhanging
> it by a few inches.

He found it was better letting the front overhang further than you think.
Later, after a few weeks of use the rest of the frame begins to move a
little, as most new additions do, and the wear factor means the seat back
will go quite a bit further than it maybe should. An extra inch at the
start isn't a problem, but moving them later can be ..

> now to invent a method of holding it down securely while still being
> removable without use of tools...

Bolt through from underside, with hole drilled to suit frame holes then use
R-clips and large washers .. swot I use for the Trials bike trailer ..

--
Paul ...

(8(|) ... Homer Rocks

"A tosser is a tosser, no matter what mode of transport they're using."

"Paul - xxx" <[email protected]> wrote in message
news:[email protected]...
> Austin Shackles vaguely muttered something like ...
> > anyone with these 90/110 etc. rear benches know if there's supposed to
be
> > anything holding the seat cushion on?
>
> Not as standard .. mate used sticky back velcro strips ..
>
> > doesn't appear to be on this'n.
> > the seat back part is obviously normally bolted down to the wheelbox and
> > the base part is hinged, and clearly rests on the wheelbox, overhanging
> > it by a few inches.
>
> He found it was better letting the front overhang further than you think.
> Later, after a few weeks of use the rest of the frame begins to move a
> little, as most new additions do, and the wear factor means the seat back
> will go quite a bit further than it maybe should. An extra inch at the
> start isn't a problem, but moving them later can be ..
>
> > now to invent a method of holding it down securely while still being
> > removable without use of tools...
>
> Bolt through from underside, with hole drilled to suit frame holes then
use
> R-clips and large washers .. swot I use for the Trials bike trailer ..

Or go make some pretty holes in a scrap people carrier the likes of a
Espace.. they have nifty flush mounted seat brackets so when the seat is
removed the only danger is the odd sticky toffee geting stuck in the hole.

Lee D

On or around Wed, 8 Sep 2004 13:38:54 +0100, "Paul - xxx"
<[email protected]> enlightened us thusly:

>Bolt through from underside, with hole drilled to suit frame holes then use
>R-clips and large washers .. swot I use for the Trials bike trailer ..

that's near enough what I had in mind, except that the gas tank is under the
rear floor precluding access, so I might instead make a plate with a
sticking-up sprog on it and weld it to the floor from above. Seat belt
mounts will of course have to bolt through, but they're right near the back
and the tank isn't in the way, I hope.

I intend probably to have the mounts for the seat either side, anyway, so
maybe the access ain't a problem.

"Austin Shackles" <[email protected]> wrote in message
news:[email protected]...

> I intend probably to have the mounts for the seat either side, anyway, so
> maybe the access ain't a problem.
>

In that case... shoot bolts as in ... http://www.foxlea.co.uk/bits.html
Suitably overengineered to instill confidence in the parents of the wee
little ones you escort.

Lee D

On or around Wed, 08 Sep 2004 20:36:42 GMT, "Lee_D" <[email protected]>
enlightened us thusly:

>"Austin Shackles" <[email protected]> wrote in message
>news:[email protected]...
>
>> I intend probably to have the mounts for the seat either side, anyway, so
>> maybe the access ain't a problem.
>>
>
>In that case... shoot bolts as in ... http://www.foxlea.co.uk/bits.html
>Suitably overengineered to instill confidence in the parents of the wee
>little ones you escort.

I bet they never look at it. very trusting, some people. Granted, if it
was obviously held in with string, they might not be amused.

gotta hunt some steel for the underframe today.

The passengers backside


--
Larry
Series 3 rust and holes

"Austin Shackles" <[email protected]> wrote in message
news:[email protected]...
>

> anyone with these 90/110 etc. rear benches know if there's supposed to be
> anything holding the seat cushion on?

On or around Thu, 09 Sep 2004 07:33:04 +0100, Austin Shackles
<[email protected]> enlightened us thusly:

>On or around Wed, 08 Sep 2004 20:36:42 GMT, "Lee_D" <[email protected]>
>enlightened us thusly:
>
>>"Austin Shackles" <[email protected]> wrote in message
>>news:[email protected]...
>>
>>> I intend probably to have the mounts for the seat either side, anyway, so
>>> maybe the access ain't a problem.
>>>
>>
>>In that case... shoot bolts as in ... http://www.foxlea.co.uk/bits.html
>>Suitably overengineered to instill confidence in the parents of the wee
>>little ones you escort.
>
>I bet they never look at it. very trusting, some people. Granted, if it
>was obviously held in with string, they might not be amused.
>
>gotta hunt some steel for the underframe today.

OK, got the bits fro the frame, but yet to actually construct anything. no
sense in being too hasty...

"Austin Shackles" <[email protected]> wrote in message
news:[email protected]...

> OK, got the bits fro the frame, but yet to actually construct anything.
no
> sense in being too hasty...

No...you've got till the morning ;-)

Lee D

On or around Fri, 10 Sep 2004 17:29:56 GMT, "Lee_D" <[email protected]>
enlightened us thusly:

>"Austin Shackles" <[email protected]> wrote in message
>news:[email protected]...
>
>> OK, got the bits fro the frame, but yet to actually construct anything.
>no
>> sense in being too hasty...
>
>No...you've got till the morning ;-)

currently got a rather uncomfortable swelling in a very private place, which
has rater curtailed crawling around making and fiddling. hope it goes away
soon, or I'll have to go to the quack.

however, I don't need this seat for a week or so at least - not supposed to
pick up unauthorised sprogs, and they've yet to request transport from the
council.