Diesel cooling system problems

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
G

Gazza36

Active Member
Posts
250
Location
South West
Dear all, apologies if this has already been covered elsewhere but it seems quite specific, so recently the radiator hoses would remain hard even after a whole day standing and were starting to work their way off the radiator. Upon undoing the expansion tank cap the pressure would release. So I replaced the cap with a spare one I had and that seemed to solve the problem.

However, now the hoses are coming off again, but not staying hard and coolant is leaking from the cap. The head was replaced about eighteen months ago so I will be slightly upset if the head gasket has gone already, it has to go in to the garage anyway because some of the injectors are leaking, any help greatly appreciated.
 
Needs a static and dynamic pressure test. Static should hold 15 PSI without falling. Dynamic pressure test should run at 5 to 7 PSI warm at idle. Also get the cap tested.
 
Last edited:
Going in Thursday, I'm guessing the static test is with the engine off and if the reading is low it indicates there is a leak somewhere, i.e. the head gasket, and the dynamic is running and if that is high it is because the gases are getting in, cheers.
 
Gazza36 said:
Going in Thursday, I'm guessing the static test is with the engine off and if the reading is low it indicates there is a leak somewhere, i.e. the head gasket, and the dynamic is running and if that is high it is because the gases are getting in, cheers.
Click to expand...

Yes apply tool engine off and pressurise to 15 psi. Pressure should hold. Apply tool and start engine pressure should be 5 to 7 psi at idle when engine up to temp. Any fast rise in pressure above that at this stage would mean gas is entering system.
 
Gazza36 said:
Going in Thursday, I'm guessing the static test is with the engine off and if the reading is low it indicates there is a leak somewhere, i.e. the head gasket, and the dynamic is running and if that is high it is because the gases are getting in, cheers.
Click to expand...
Sadly, a cracked head is more likely then HGF:(
 
Ok so eventually i just bought a pressure tester, it holds 15psi no problem at all but when running the gauge shows nothing, am I doing something wrong? Cheers.
 
Gazza36 said:
I am going to flush the system and start again.
Click to expand...

The drain plug is at the bottom of the radiator AND there is a drain screw on the cylinder head (tricky to find, its located underneath),
once drained, put screw and drain plug back in, fill up at header tank until you can get no more in, start engine, keep topping up until it will accept no more, top hose will become hot after 10 mins or so. re check over next few days.
On the first refill you can squeeze all the hoses to get air out.
It takes a minute or so of the engine on until the level goes back down again then you need to make sure you have enough coolant mixture made up to top up with...
50/50 mix of GOOD anti freeze....follow the instructions on RAVE.
 
When I refill mine I leave the engine running and squeeze each pipe like I'm inflating a blood pressure monitor. Then top up and continue. Sometimes it goes straight in and others it is a complete PITA.
 
ok so i had another look, pressurised to 15psi with the engine off and warm, I can't test it running because for some reason the tester doesn't seem to be able to work like that, this time I noticed that the pressure did drop really slowly and I would get a drop of water come out of the overflow pipe, when driving it will lose coolant from this pipe.
 
Ok so managed to read some pressure while running after a decent time, it had reached about 3 psi when i stopped, should i leave it running longer to reach 5 to 7 psi and should i get it sniffed? Cheers.
 
Gazza36 said:
Ok so managed to read some pressure while running after a decent time, it had reached about 3 psi when i stopped, should i leave it running longer to reach 5 to 7 psi and should i get it sniffed? Cheers.

If it is only getting to 3 psi after a short run it will be fine. If you had a combustion gas leak it would shoot up a lot quicker and to a much higher pressure than that.
Click to expand...
 
I dont see how a leak from the bottom will cause the overflow at the top to dribble. have you checked the viscous fan, if thats not working ,its not forcing air through the radiator at low road speeds
 
Just clutching at straws, the fan isn't that old but then I guess that doesn't mean anything with these as the radiator isn't either, the place where I got it said he has a customer that's been through three in a not considerable amount of time. The new tank is fitted so I shall see if that makes any difference.
 
You must log in or register to reply here.

Similar threads

enjoi
P38A My good friend, coolant leak, is back!
Replies
7
Views
1K
Andy Burrell
Andy Burrell
stemac33
P38A Range Rover P38 2.5 dt for sale
Replies
2
Views
1K
stemac33
stemac33
enjoi
P38A Coolant woes
2 3 4
Replies
72
Views
7K
kermit_rr
kermit_rr
P
Advice needed for fixing a VM 2.5
Replies
9
Views
1K
lynall
L
Pauldw
Disco 2 TD5 - Heater Blowing Cold
Replies
2
Views
926
Interceptorxj
Interceptorxj
Back
Top