What have you done to your Freelander today

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Alibro said:
It might be worth trying to tighten up the bolts first. They are fitted with lots of thread lock so if you do need to replace them the bolts will fight you to the end. :(
I used a standard spanner to remove mine and had no issues apart from the constant stream of swearing as I fought them. My torx sockets are 1/2" and were too big to fit.
Click to expand...
My 2 centre ones are torx bolts so I will bite the bullet and buy a set of female sockets
 
DCUNNINGHAM said:
My 2 centre ones are torx bolts so I will bite the bullet and buy a set of female sockets
Click to expand...
Get 3/8" rather than 1/2" if you can. Like I said my 1/2" torx sockets didn't fit as there isn't much room. Using a spanner was my cheapo answer.
BTW I've removed and refitted 4 or 5 props using 1/4" sockets on the torx bolts with no problems.
 
Alibro said:
Get 3/8" rather than 1/2" if you can. Like I said my 1/2" torx sockets didn't fit as there isn't much room. Using a spanner was my cheapo answer.
BTW I've removed and refitted 4 or 5 props using 1/4" sockets on the torx bolts with no problems.
Click to expand...
Cheapskate! I used (probably imperial) sockets to remove and replace the prop the first time - but torx are used quite a bit on Freelander so bought myself a set of torx sockets after that. Admittedly I haven't used them much, but they do make life easier - and more reliable.
 
image.jpeg
Got round to breaking the prop shaft to replace vcu support bearings. Back shaft took 5 minutes, the front shaft was a sod and it was only when I realised I needed a bigger hammer that I got it off. WD40 on the bearings and will give them a go tomorrow.
 
Don't believe it
The master cylinder is leaking again !!
At the clutch pedal but now my gears are more or less impossible
The clutch arm is fine moves back and forth with no effort 2 fingers
I don't know if there a crap make or there is more to it
They last a couple of days then caput it starts leaking
 
I used to think Bearmach stuff was OK. Now I don't.
If you don't want to go for OEM from somewhere like Rimmers then maybe try ordering a kit from a local car parts shop. At least you can easily take it back if it fails.
 
I don't have a problem with pedal height it just leaks at the seal on pedal end after 2 days
I'm going to look for a different supplier
The two I've put on are obviously cheaply made crap
 
Hopefully not :)but does make sense,you have a lot more patience then me,I’ve spat my dummy out with mine just because I can’t get the mg mirror to work right :mad:
 
Danyou said:
Hopefully not :)but does make sense,you have a lot more patience then me,I’ve spat my dummy out with mine just because I can’t get the mg mirror to work right :mad:
Click to expand...
I'm in to minds now to change the clutch or drive it and see if it leaks again but then if it does it's more expense I just can't understand why the slave doesn't break instead of the master
Also the gearbox looks hard to remove lol
 
DCUNNINGHAM said:
I'm in to minds now to change the clutch or drive it and see if it leaks again but then if it does it's more expense I just can't understand why the slave doesn't break instead of the master
Also the gearbox looks hard to remove lol
Click to expand...
I really wouldn’t fancy getting that involved in the car,little bits and pieces are enough for me :)
 
You must log in or register to reply here.

Similar threads

B
Freelander 1 Freelander prop bearings replacement td4
Replies
15
Views
541
andyfreelandy
andyfreelandy
O
Freelander 2 diff removal
Replies
7
Views
265
Nodge68
Nodge68
andyfreelandy
Other New Project starting today
Replies
3
Views
288
Alibro
Alibro
P
2006 Facelift TD4 Auto turbo vacuum boost solenoid
Replies
11
Views
504
andyfreelandy
andyfreelandy
P
Freelander 2 4wd problems
Replies
3
Views
615
pauld2296
P
Back
Top