eas kit

[mutsnutz]

ordered a new pipe from island 4x4 last night so fingers crossed it will be here in a day or two then the fun begins again

 

[mutsnutz]

new pipe arrived today and still not working ive ordered a new block compressor driver cos ive had enough of the rather expensive doorstop :fighting::fighting::fighting:

 

[mutsnutz]

sorry to bring this old chestnut up again but having replaced valve block ,compressor and driver still no air checked all pipes that i can see for leaks and none found but the one thing that i did notice is that with the eas software the compressor works great lots of air pumping out but once the ignition is switched on i get zilch any ideas why its doing this

 

[p38 prius lol]

sorry to bring this old chestnut up again but having replaced valve block ,compressor and driver still no air checked all pipes that i can see for leaks and none found but the one thing that i did notice is that with the eas software the compressor works great lots of air pumping out but once the ignition is switched on i get zilch any ideas why its doing this

the engine needs to be running for the pump to work

 

[mutsnutz]

when on i get nada pump doesnt work

 

[Datatek]

Thermal trip gone in the compressor.

 

[mutsnutz]

Thermal trip gone in the compressor.

how do I repair that ????

 

[Datatek]

how do I repair that ????

Strip the motor, unsolder the trip and solder in a new one. do a site search the part number has been mentioned a few times.

 

[mutsnutz]

Strip the motor, unsolder the trip and solder in a new one. do a site search the part number has been mentioned a few times.

cheers data

ive just plugged in my old pump and its pumping ok but still no air getting to the bags or air tank

 

[Datatek]

cheers data

ive just plugged in my old pump and its pumping ok but still no air getting to the bags or air tank

Maybe you old pump doesn't make enough pressure?

 

[mutsnutz]

its a possibility but just had new seal kit

 

[Datatek]

its a possibility but just had new seal kit

Test it, look at Wammers How to in the How To section.

 

[mutsnutz]

just done another test and its making good air , plenty air at blue pipe no air escaped at outlet just cannot figure why its not lifting the vehicle from access mode the access light is steady and standard light continues to flash

 

[Datatek]

just done another test and its making good air , plenty air at blue pipe no air escaped at outlet just cannot figure why its not lifting the vehicle from access mode the access light is steady and standard light continues to flash

Plenty of air? At what pressure?
Normal reason for not lifting when the lights are as you say is lack of air pressure.

 

[mutsnutz]

how do i find out what pressure i dont have a gauge

 

[Datatek]

how do i find out what pressure i dont have a gauge

Look at Wammers How To. Take the blue pipe off, run the compressor from the software or automatically, stick your thumb over the end of the pipe, if you can stop the air the compressor is NBG.

 

[mutsnutz]

its gone up to height the dozy tit that i am it was sucking like a prossie in a back alley till i put the filter on then ohh no it wouldnt suck:doh: it was blocked so big thanks to all who have helped me out

lesson learnt check the filter first :behindsofa:

 

[marcinbrighton]

Pleased you got it sorted Fantastic analogy too

 

[mutsnutz]

Pleased you got it sorted Fantastic analogy too

cheers mate just need to find the part number for Thermal trip now to sort my other compressor

 

[p38 prius lol]

cheers mate just need to find the part number for Thermal trip now to sort my other compressor

RANGE ROVER P38 EAS PUMP AIR COMPRESSOR THERMAL SWITCH | eBay