Clanforbes
New Member
- Posts
- 1,503
- Location
- Perthshire
I got my EKA code from LR for it today.
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
robint
Well-Known Member
- Posts
- 7,057
i bought this !!!
needs a bit of welding but all the major parts have been done
needs a bit of welding but all the major parts have been done
Clanforbes
New Member
- Posts
- 1,503
- Location
- Perthshire
Got it started - for about 15 minutes before it died, again.
Took out the dash to clean it and replace some bulbs.
Bought a spare set of injectors.
Took out the dash to clean it and replace some bulbs.
Bought a spare set of injectors.
Last edited:
Yogi Bear
New Member
- Posts
- 174
- Location
- Chesterfield
I went outside with a swear box and stood between the Rangie and the Disco. I proceeded to empty my pockets into the swear box then left.
Muddy Gonzo
Banned
- Posts
- 2,509
- Location
- Chesterfield
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Decided to find out why me heater blower & aircon dun't work.
Discovered that the heater switch was fried. But more importantly I discovered that to change the switch you have to remove the entire dash and front fascia.
Also found out that there was no power supply to aircon or blower and that the ****er who installed the aircon decided that he only needed to use Blue or green wires! As a result I've spent all day tracing wires and changing relays as well as running a new feed and ignition switched relay. The good news is that everything Inc AC compressor clutch is now working. The bad news is that I cut the AC belt tuther day cos the tensioner pulley bearing was knacked and making a racket. :doh:
Discovered that the heater switch was fried. But more importantly I discovered that to change the switch you have to remove the entire dash and front fascia.
Also found out that there was no power supply to aircon or blower and that the ****er who installed the aircon decided that he only needed to use Blue or green wires! As a result I've spent all day tracing wires and changing relays as well as running a new feed and ignition switched relay. The good news is that everything Inc AC compressor clutch is now working. The bad news is that I cut the AC belt tuther day cos the tensioner pulley bearing was knacked and making a racket. :doh:
Last edited:
thought i'd change my front axle before it let's go(knackered cv and splines worn on input) have both axles from the range rover that i destroyed for the engine and box (it was beyond repair as i didn't fancy spending the rest of my life welding)
so off we go,wheels off,calipers off,prop off to do uj,steering box disconnected,panhard disconnnected,shock lowers undone,raius arm to chassis undone,lift chassis with forklift(always handy to have one of these to hand when working on the bastard)and kick axle out,easy.
drag replacement out to compare and it's got the larger chassis mounts on the radius arms,no biggy,just swap them.3 of the bolts fly out like you put them in yesterday on axle one,the last being quite happy where it was. axle 2 was exactly the same with one c*nt of a bolt that wasn't coming out in a hurry. think **** it,i'll pull the hubs and half shafts out and swap the diffs and all will be good in the world,bearing in mind axle 2 has not turned a wheel in 2 years and has been sat under a rotting range rover. oh joy! 12 sided bolts with more corrosion than is really needed. spend an hour making sure i can undo them all,which i can eventually. jump onto axle 1 to do same,hex bolts with locking tabs,piece of **** this,had two bolts out in a flash,just started on third bolt and noticed ones got six bolts,the other seven. not discouraged at this point i push on and decide that bastard radius arm bolts from hell must be encouraged to leave home(much like my son) 2 hours later after much sweat and tears (read 2 hammers,broke one,grinder,3 cutting discs,lots of manual labour)they decided they'd had enough and let loose their grip.
i decided i'd had enough at this point and retired to my happy place,which is nice.
what is it about the fourth bolt?
so off we go,wheels off,calipers off,prop off to do uj,steering box disconnected,panhard disconnnected,shock lowers undone,raius arm to chassis undone,lift chassis with forklift(always handy to have one of these to hand when working on the bastard)and kick axle out,easy.
drag replacement out to compare and it's got the larger chassis mounts on the radius arms,no biggy,just swap them.3 of the bolts fly out like you put them in yesterday on axle one,the last being quite happy where it was. axle 2 was exactly the same with one c*nt of a bolt that wasn't coming out in a hurry. think **** it,i'll pull the hubs and half shafts out and swap the diffs and all will be good in the world,bearing in mind axle 2 has not turned a wheel in 2 years and has been sat under a rotting range rover. oh joy! 12 sided bolts with more corrosion than is really needed. spend an hour making sure i can undo them all,which i can eventually. jump onto axle 1 to do same,hex bolts with locking tabs,piece of **** this,had two bolts out in a flash,just started on third bolt and noticed ones got six bolts,the other seven. not discouraged at this point i push on and decide that bastard radius arm bolts from hell must be encouraged to leave home(much like my son) 2 hours later after much sweat and tears (read 2 hammers,broke one,grinder,3 cutting discs,lots of manual labour)they decided they'd had enough and let loose their grip.
i decided i'd had enough at this point and retired to my happy place,which is nice.
what is it about the fourth bolt?
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
i sold me overdrive fer £100...........
the rest of the landy is for sale in bits(cause its stripped) but i can't list it here as it would take for ever due to the fooking for sale bit being a poo idea
the rest of the landy is for sale in bits(cause its stripped) but i can't list it here as it would take for ever due to the fooking for sale bit being a poo idea
Sirus
Your all Banned except me
- Posts
- 22,196
- Location
- The Country of Black
yer a tit..... i ebayed mine for 535 quid 3 weeks ago:doh::doh:
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
well i was going to put if up for sale on here but i can't get on with the for sale bit, its crap and only really set up for selling whole cars and even then a bit obtuse
we could do with a for sale section that you can just post a plain text add without all the bollocks (basically just a for sale section where you start a thread to sell yer ****
Sirus
Your all Banned except me
- Posts
- 22,196
- Location
- The Country of Black
You'll get more for em on ebay....people will pay silly money for stuff on there.
thought it was mine!
New Member
- Posts
- 8,236
your right about silly money on ebay one landrover no id a couple of grand a fool and his money ebay parted:crazy:
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
but i fookin hate ebay every time i have ever sold anything on there, even though i am 100% honnest with my auctions, i have people come and haggle or say 'its not how you described it/how it was in the pictures' either that or it sells for much less than its been worth
bustersbus
Well-Known Member
- Posts
- 13,755
- Location
- Near Dumfries, Scotland
Ah'm sure ah heard somewheres that ye should start yer biddin' price just below what ye want fur it... dunno if it;s true or not tho'
When ah used it, ah never had any probs apart from one person who didn't check the part numbers ah posted up:doh:
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
[/COLOR]
Ah'm sure ah heard somewheres that ye should start yer biddin' price just below what ye want fur it... dunno if it;s true or not tho'
When ah used it, ah never had any probs apart from one person who didn't check the part numbers ah posted up:doh:
you can..... but its gonna cost ya....
bustersbus
Well-Known Member
- Posts
- 13,755
- Location
- Near Dumfries, Scotland
Aye true, but if ye want rid as it's no use to you then it's worth it... better than chuckin' it
