Search results

Hi all, The disco 1 shall require welding in the coming weeks, the welding require is at the rear, where the chassis mounts connect to the body (body side). I've sourced someone to carry out the welding, the question is, would it be easier to purchase these inner sill mounts to weld in? Rather...

Hi all, Need to replace the bonnet release cable on the disco 200tdi - can anyone inform me as to which type there is a TA and MA? https://www.ebay.co.uk/itm/230913576836?hash=item35c3858f84:g:WxoAAOxyDgRQ9tM5 https://www.ebay.co.uk/itm/221178316719?hash=item337f4147af:g:U6UAAOxyQ45Q9tM2 Thanks

Cheers Pawl, good to have your feedback.

Hi all, Thought I would update here - it turned out to be the vacuum pipe that connects into a T-piece which in turn goes into the heating system? It's slightly concerning as this pipe has split, I cut the end off and reconnected but probably replace this as it's quite a concern that the...

Thanks Ivor, think I just need to bite the bullet and purchase a new motor!

Hi all, So after getting all the internals moving and back on the car turns out as above, the plastic cog is stripped. Would anyone know where to purchase a spare or some kind of 3d printed version?

Ivor, thanks a lot - essentially it's just a bulb that pops in place, just tried and it worked!

Ah meant alloys - they came with these maybe it was an upgrade the twist alloys: https://picclick.co.uk/Land-Rover-Discovery-1-200-Tdi-Range-Rover-273922232219.html They look more grey to me..

Is there anything the bulb slots into like a bulb holder a bit like you get on the rear lights for example, or would the bulb just go in?

Hi all, Does anyone know the original colour of the 200tdi disco 1 wheels? The center caps on mine need a refurb and would make her look great! Thanks

Hi all, The interior trunk/boot light on the disco was not working, from taking it out and realise there is a missing bulb and perhaps something that slots over the bulb to hold this in place. Could anyone let me know if the bulb just sits inside the outer plastic housing somehow, or is there...

Thanks Ivor. I managed to take this out of the disco yesterday, and take everything apart the single plastic gear looks to be in working order, I'm unsure of the internals of the actual motor itself. The pinion was rusted and seized to the housing, manage to get this apart and will lubricate...

Not contaminated, just been stood for a while - could well be rust on the surface, seized pistons or the servo will check later today thanks!

So removed the wiper and nothing is moving from the exterior point of the land rover. I haven't looked inside under the plastic cover but believed this to be rusted in place, how do you free this up?

Hi all, Disco 1 200tdi rear wiper motor can hear turning spinning or doing something but the wiper is not moving, guessing the pinion is seized any advice on how to fix this. Thanks!

Thanks all - I'll check the servo vacuum first then update this thread. Haven't changed the pads or discs recently, but thought the build-up for rust etc would run off after some brake tests.

Hi all, Working on the brakes recently on the disco, not driven for 18 months or so. Yesterday after bleeding and changing some of the lines went for a careful drive, on pressing the brake pedal this felt hard, but not the usual soft to hard. The pedal effectively presses the calipers in but...

Thanks guys, going to clean this up!

Hi all, Carrying out a service on the 200tdi and noticed a filter to the rear of the vehicle underneath, does anyone know what this is? Thanks

Hi all, Yet another thread here. First of all thoughts on replacing discovery 1 200tdi discs, they have been sat for around 18 months, would a couple of careful drives see them back to normal? Replacing the discs on this look more involved than first thought, it's not a standard replacement...