Search results

little tip I was given Check the breather pipe from the top of the rad (top left as you look from the front) to the overflow is flowing, quick check showed to me by mechanic is it will be hot at both ends if its flowing, if not that could be blocked airlocking the rad, quicker than taking the...

hi all, was looking for kicker lites on ebay and spotted this nano kicker, anyone know anythign about them good, bad or other? Range Rover P38 EAS Nano Kicker Suspension Reset Tool | eBay

I started with that on mine, but only found the split when i removed the hose form the MAF to plenum chamber, it was in one of the ridges on the underside of the hose

i had this with mine, check the intake hose for leaks/splits after the MAF. could be letting in too much air after the ECU has decided how much fuel to inject. my garage also re sealed my plenum chamber as that was leaking air in

I don't know if its the same on the Diesel as the Petrol but check the breather pipe from the top of the rad to the overflow is flowing, quick check showed to me by mechanic is it will be hot at both ends if its flowing, if not that could be blocked airlocking the rad, quicker than taking the...

just thinking out loud, if I was to short across this pins of the connector with a wire should it send the into the red, proving that at least their is a connection to the dash?

its hardly getting into the blue, I am hoping not I don't want to have to change it again, only just stopped it loosing coolant and got all the air locks out.

I have looked at RAVE and the comment in my post are from what I understand. but could be completely wrong

fan works fine, will double check the rad, will have to wait for it to cool down as its all red hot at the moment (hopefully without being too hot). I would expect it to heat up to normal running temp after 40min trip home in Friday night traffic even with stat fully open.

not sure, does not even move on a long run, would have thought the V8 would need to get rid of as much heat as possible via rad. certainly wanted it when over flow was blocked.

Hi all, Seems to be one thing after another with with my P38, finally stopped it loosing coolant and thought that would be it for a little while but now the temperature gauge on the dash has stopped working so if it does overheat I wont know until it too late. so was wondering if any one here...

its a 4.0 and the block was pressure tested so hoping not

Would I be able to see evidence of the leak without taking anthing apart? any clue as which direction to look from, front, left or right side?

Heads were done as HG had blown, garage pressure tested the block to check for slipped liners before proceeding with skimming and refitting

Hi, I have looked over previous threads and cannot find an answer that matches so hoping you guys can help. I appear to be losing coolant about 1/2 litre every 40 miles Just had HG done and heads skimmed so hoping it’s not that (paranoid about coolant level hence the...

mine did a similar thing the gears/shaft had separated from each other, rather than replace the motor the garage just opened up the flaps so air is always blowing at the screen. quicker than taking everything out to swap the motors.

perfect, cheers

Cheers, I have looked and most of the website and all have plenty of hoses, but I cannot tell from the descriptions (I never believe pics) if its the right one, I was looking for the part numbers of those 2 hose so I can confirm i have the right ones. I seem to be going round in circles and...

Hi all, I have been searching for days and still getting no where, so hoping the collective minds here might be able to help I have a P38 1998 4.0 SE and I want replace a all the of the hoses whilst i am putting a new stat I have found all the hoses that go around the bottom of the engine and...

Hi, Found a split in one of my P38 (1997 4.0 v8 GEMS) cooling hoses (causing random water loss and over heating, gaffer tape is holding it for now but thinking i need to replace it and whilst at it do all the other hoses can anyone see a reason not to buy this kit P38 Radiator Cooling Hose...