Search results

Anyone near Glasgow have a nanocom that could try reset my ecu addaptive values?

Car is a 2002 52 reg 4l v8 Getting multiple misfire code on diagnostic along with misfire on cylinders 2,6 and 8. Have replaced lambda sensors and compression tested bank 2 with following results 2 -175psi 4 - 165psi 6 - 150psi 8 - 150psi No other fault codes. Looking for suggestions on what...

Next problem: Discovery 2004 v8 auto My eml came on some time ago and i read the fault codes and got p0141 & p0161 heater circuit either bank sensor 2, changed the o2 sensors for new ones that was fine for about 40 miles then eml came back on. I have replaced the o2 sensors again for new ones...

Anyone got a nanocom or similar that could help resync my keys? Near Milngavie? Car is a 2004 disco 2 v8

A long story so will cut to the chase.my 2004 disco v8 battery was flat after not using the car for a couple of weeks, it jump started no bother and did a long round trip, i then used it the next day no problems, went to go out that afternoon and the key fob on either key (i have both) will not...

Hi is there anyone in or around glasgow with an obd2 reader that can read my 2004 disco v8 fault codes? Mine will not connect comes up link error. Or is there any software i could download as i have a obd2 to usb cable? Cheers

Having had to many problems with Lucas 4cu efi system I am going back to twin su carve. Problem is two pipes coming from coolant pump housing one is blocked off as not used on efi however it feeds heater matrix through pipe under inlet manifold, has anyone had same problem???? And how did you...

Anyone in or around glasgow that has a working 4cu ECU that i could try on mine? Engine runs great but every so often it just dies then wont restart for ages??? Looking to try a known working one to rule it out. Am now at stage where I am tempted to put carbs on it!!!! Cheers

Hi I have a 3.5 efi flapper from a range rover now in my 90. It was running great went a run in it for about 30 miles (had already been using it for a week or so 20 miles a day) then it started missing and cutting out. I cleaned all plugs and checked for spark (good spark). Plugs get soaked...

I was wondering if it is possible to adjust the idle on a 1988 3.5 EFI engine (from range rover classic) as its in a 90 there is no rev counter so i can only tell its high by listening. Cheers for any help

I have converted my 90 V8 from carb engine to a range rover lucas efi 3.5 engine runs sweet except overheats. Radiator gets warm after switching off - but blows cold air through matrix. With pipe off matrix there is very little water coming through - is this likely to be pump or could it be...

I have fitted a tow bar to my 1997 4.6HSE only problem is i cant find wiring diagram to connect wires from tow bar electric socket to the spare loom behind drivers side rear lights. Can anyone tell me which port on connector goes to which colour wire on the car? Many Thanks Brian

Hi In my long saga of engine trouble my problem is shott bottom end bearings. The engine is still in and I hope to keep it there to replace the bottom shells and the oil pump just in case it is on way out. I have tried several times to download and run the rave software but with no luck. So i'm...

Hi I am trying to remove rocker covers on my 97 4.6hse I have removed 2 bolts either side rockers and undone the 8 holding inlet manifold is there anything else i need to remove as it still feels solid?? thanks

How hard is to change a 4.6 litre engine in a P38 Auto? Also how heavy does an engine weight? Bry

Currently looking for 4.6V8 engine out a pre 99 for my p38 around glasgow anywhere i could try? I also have for sale a set of hurricane P38 alloys with 3 good tyres 4th could do with replacing. Buyer must collect Offers to [email protected]

Coming up a hill earlier today box kicked down then oil drip light came on then clunking from engine, its the sound i know that is the piston is meeting the valves, what is more likely though? - Con rod or bearings or bent valves? I know its hard to diagnose when not looking at it, noise is...

Hi all hope you can help I am getting a vibration at 15 - 20 mph has anyone got any suggestions? have changed wheels but not made any difference seems to come from passenger side front but not certain? Rangie is 97 4.6 hse ltd edition Thanks

HI all I'm looking to fit 06 range rover alloys to my 97 P38 and was wondering if anyone knows of anywhere in glasgow or anyone in glasgow who has a set of spigot rings? I know its a long shot but would like to fit my wheels tomorrow or saturday. Many thanks

Hi i have a 97hse 4.6 Looking to see if anyone can shed any light on why i am getting a judder below 20mph? Its coming through steering but only does it every so often? ANd if i speed up it goes away but stays if i apply the brakes? Any help would be great Brian