Search results

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. nigelrw

    hello mozz smith - you are my last best hope - 2001 4.6 P38 in lock out - have tried to enter...

    hello mozz smith - you are my last best hope - 2001 4.6 P38 in lock out - have tried to enter EKA code but red light keeps flashing and alarm goes off if i turn on ignition after - I am open to all suggestions - I did allow battery to go flat but is now fully charged of course key no longer work...
  2. nigelrw

    What did you do with your Range Rover today

    Just rebuild suspension air compressor all working fine next job to drain and refill gearbox
  3. nigelrw

    L322 Sill repair panels - supplier of Bodywork required

    Thank you all for your input and fashion sence !! I think way forward will either be to make up panels or get hold a body and cut out the part need which is somewhat more economical than buying two side panels once again many thanks
  4. nigelrw

    L322 Sill repair panels - supplier of Bodywork required

    Thanks Saint.V8 - so far it looks like no repair panel but waiting on some suppliers to get back - can get the "side of the car" from LR for approx. £1.5k - looks like getting under and having a poke around to see just how serious this could be
  5. nigelrw

    L322 Sill repair panels - supplier of Bodywork required

    My son's L322 is in need of new outer sills o/s & n/s on his 2004 3.0D - Having spoken to our local Land Rover dealership I am recovering from news they can only supply side of car rather than a repair panel and after trawling web I am no further forward- has anyone had to replace panel and if...
  6. nigelrw

    What did you do with your Range Rover today

    Replaced throttle body cooling plate and cleaned throttle body - job I have been meaning to do for ages - now to give the car a good clean inside and out
  7. nigelrw

    Radio removal

    Datateck - it seems you are havinga rough time with your P38 sorry to hear this- try the link below Heater Core O-Ring Replacement I found this very useful - got extra set of "o" ring just incase & changed the temp sensor - that said I did cut out the air duct and put back with duck tape to...
  8. nigelrw

    Cheap oil with free filters! Be quick.

    Many thanks for pointing this out
  9. nigelrw

    Another EAS problem

    Thanks Stufer - I replaced presure switch when I rebuilt valve block just in case should have said sorry
  10. nigelrw

    Another EAS problem

    P38 2001 4.6 100k - The EAS system has been giving me some worries recently -I have replaced all four bags (leak on rear) and rebuilt valve block and compressor - system works well with no dropping down over night and from access mode she is up to correct hight within 15 secs so all seems fine...
  11. nigelrw

    Alarm sorted, but keys not working?

    I too had same problem on a late 2001 4.6 - check your little red light flashes when you press button - put key in drivers door and press and hold down lock button - still holding lock button turn key anti-clockwise to lock door but hold it there for at least a slow count to 10 - you should hear...
  12. nigelrw

    EAS - Am I going Paranoid

    Thank you for the idea that the storage side could be at fault will check tank and pipework just in case :)
  13. nigelrw

    EAS - Am I going Paranoid

    Many thanks for the replies - will clean connectors first and if no different looks like the pressure switch again many thanks
  14. nigelrw

    EAS - Am I going Paranoid

    Please some advise - but I must let you know actions taken thus far - some weeks ago the EAS pump seemed to be working overtime but not going into fault - suspected leak but could find none - bags looked to be original so started at that point and changed out the four of them for new Dunlops...
  15. nigelrw

    Foam filter on scuttle panel

    Good information sas1810 - I will have to do this - have some stainless steel mesh on order - will take pics and post when job done
  16. nigelrw

    Who wants to do my o rings??

    and me a good vegetarian :D
  17. nigelrw

    Who wants to do my o rings??

    Hi Druim The air duct was not going to come easy without a fight - cutting the unit out gives fair access and duck tape after worked wounders but agree with you 100% spent more time reseaching than doing the task :rolleyes:
  18. nigelrw

    Hawkeye V5 Manual

    Hi - have used a free FTP site on the web search for "yousendit" you can open free account - may be of use ?:)
  19. nigelrw

    Who wants to do my o rings??

    Did mine a few weeks back - the info on short cut is very good as are the excellent pictures on Landy Zone do a search on matrix "o" rings - would suggest it could take upto a day and make sure you replace the draw bolt with a stainless steel allen head bolt M5 x30mm (I seem to recall) - other...
  20. nigelrw

    Foam filter on scuttle panel

    Having checked the thread jamesblake suggested(many thanks for pointing in right direction) it seems not too hard but getting spare bits is good insurance - stainless must be correct way to go
Back
Top