Search results

Since I never use overdrive I have been thinking about selling it. Just now getting close to 500 miles since it was installed last fall. Bought new from sycrogearboxes October 2020. Located in Finland €1000 but no shipping.

On my 88 I had a local upholstery shop sew up my headliner, sun visors and bulkhead cover. They used room darkening curtain material which is very similar to the original. The material came from an upholstery supplier in the UK.

Today I started to install the front headliner. Looks ok. While on a drive we were on an open stretch of road so in 4th & OD we went. Almost made it to 100 :eek:. Was surprised that according to my phone GPS speedometer the landy speedo is correct.

The upholstery shop finished sewing the headliners a couple days ago. I started installing the rear first. I forgot to order the correct interior paint for the trim. Tried to get paint locally but nothing matched. Now to the front headliner.

Front edge I cut from foam but it upside-down. Rear foam and its upside-down also After cutting foam and inserted into opening. Still 3" of foam in middle but only 2" above wood base.

Angled edge went to the rear of the seat. I used 1/4" aluminum rivets to fasten the metal tray to the wood seat base. I cut the foam so it fit into the opening I cut in the base. The side foam could of been left as is. I decided to cut the side foam 1" so the upholstery would be tight...

I wanted to keep it but it was too far gone to do anything with. The front and rear axles, t-case and 3 speed transmission was the only thing that was useable.

I ran across this picture last week on our computer. While out riding my bike yesterday I got to thinking about the picture and reminiscing about the good old days. I thought about the good times I had with it and how similar the FJ40 and the Series 3 are. They ride, drive the same and the...

Just an update to this thread. I have drove probably around 300 miles since installing the factory metal seat tray. I love it. The biggest benefit is being able to see out the front without having to bend down. It still retains the full foam so no change there. All the info I could find about...

While installing the seat heater wiring I decided to replace my amp gauge with a volt gauge. Before I can finish the center dash install I will wait for the volt gauge to show up. Now when I install a larger alternator I don't need to tear the dash apart. Took the headliner to the local...

Well I was just beaming with intelligence today. I removed the dash to route the new wiring harness for the seat heaters. While I was in there it popped into my head, why don't I add key on headlights. The other day when looking for toggle switches for the seats I found an on/on 6 pole toggle...

I ordered the same motor mounts and this is what I received. Bearmach BFM 560. It only cost me £58.34

Been looking into about improving the heater. I took my IR gun and the temps at the engine heater outlets are 160°F. The temp at the metal piping is 119°F. The temp at the matrix/core is 89°F. Will start by cleaning everything then replace the control valve and install a circulation pump. Will...

My wife installed the heat pads in the seat bases. The width of the pads fit perfect on the foam but had to cut off about 6" in length. I installed the metal pan on the other base. Now to make a new wiring harness.

Started on the heated seats today. I probably should just put power to the harness as is. That would be easy and for some reason I don't like easy. First mod was to change the switches. Instead of the rocker switches I will be using toggle switches located in the center dash pod. I think it will...

Video link to shifter vibration at idle.

This morning I removed the shifter boot. I got in a hurry when installing the slick shifter and did not build up part of the area. My intention was to remove all of the original sound deadening on the transmission hump and put new on. Now its built up level. Reinstalled the boot. It was better...

I cleaned the old insulation and glue from the bonnet. Installed the new noico sheets. It is a lot brighter under the hood with the shiny aluminum sheets. Drove a couple hours yesterday. Went on the 5 mile noise test road. Virtually no change. So I thought how much is engine noise. While going...

No I did not. There are several sheets left over so I will install them there.

This morning the wife and I had a few errands to do so we took the land rover. The shifter works nice. I like how the neutral detent is but lots of vibrations when idling. Now for the sound deadening sheets, we drove the same road, same speed as before. Sound level was the same but the only...