Search results

Hello Does anyone know if any of Britpart, Rimmer or JLR will still stock the fuse box itself? It’s the small additional one under the bonnet that clips on to the main unit and just holds fuses for the heated screen. Mine has melted fuses in it due to corroded terminals and so it’s trash...

Sorry to butt in, if you just mean the plastic rail covers, under a tenner from Land Rover.... I bought a set when I took them off mine. Next day delivery. May even have been under a fiver.

Aargh, 1. Brand new nice 13mm socket from lovely new matching toolkit fell off ratchet and into engine bay somewhere) Parked over mud (it’s everywhere this weekend and car has had to be left where it died). Can’t see socket anywhere and can’t get under car without looking like a monster from...

Nope. It’s still crapping its battery charge It’s bee spot on. Then I got in it yesterday and had battery light on with ignition. Went out the second i touched the throttle. Drove. Within 15 seconds three amigos... here we go again.... Then won’t pull. SRS, fuel light, every electrically...

Oh and some other miscellaneous things like track rods (cable tied...) .... it may as well be done right if it’s got it’s innards out....

So that was expensive... LUK clutch and flywheel and cylinders bell VCU (reminds me, must send other one back to Bell) Brake pipes OEM quality Discs and pads Pierburg Fuel pump and Mahle filter New wheel bearings (garage who supposedly replaced one in July may well not have done, which is...

Thank you. I now have a boot full of bits. Got married, went on honeymoon and came back, jumped in and then.... clutch to floor... the slave cylinders leaking. So that’s beyond me. Anyone have a good reliable specialist who will do clutch Slave/master/flywheel Fuel pump And stick a new VCU...

Thanks guys. As a question, for a replacement pump and filter, is that it, or is there a gaskets and seals kit that’s needed as well? And is there a balance between a cheap pattern part and an OEM (or is there an alternative quality aftermarket supplier.).

Ah. Thank you. The 280k was at idle. Does it make a difference? She’ll run up to 3.9k now. And then I get a flash of EML which goes out as soon as I lower the revs below peak.

Thanks guys So we stuck battery on trickle charge. Restarted perfectly when battery full. Quarter of a second of turning over then fired. Low pressure fuel pump pressure 280 plus consistently. You can hear it prime for 30 seconds. Fault code left and showing same issue as before p1260 ...

hello (2004 facelift td4 manual) Ok, so now I am being told I really should have bought a Suzuki..... shame as it’s be. Running beautifully. It even now has working AC and a soft top. I have three amigo lights on. Isoft says it’s rear wheel speed sensor issue ( I have one so when I have a...

Is there not a poster on here printing them? IIRC, because of lockdown he only had white, but would be making black ones later.....

Now we get to the real LR experience. Starting to spend money on it new radiator AC Compressor Condenser Belts Battery Some preventative and common sense whilst front end is off... I’ll do some cleaning and rust protection whilst it’s all off as well

Now it works. Sticky brake pedal switch (I think) got me yellow Christmas lights to day (abs, TC, and hill descent). Went out after a rummage around the pedal Need to pick up. A proper soft top key tomorrow and hope that gets the soft top clamps to catch the lugs..... so I can leave the soft...

Thread bump (and a half). I have now acquired a soft top. Yep, all goes on. EXCEPT the clamps that fit in the body, https://www.brit-car.co.uk/product.php/112237/2821/soft_top_clamp___right_hand___freelander_1 They work on a lug system, just like the hard top. And instead of a handle, you...

That’s it. Found out JLR still have central stock for drivers side! Thank you.

Let me take a photo when it stops raining.... am looking for leaks ....

1. Had the AC failure diagnosed as a coil in the compressor. And a leak in the condenser. Disappointing, but expected. 2. Tried and failed to find some 3 door outer window seals to replace bubbled ones. Can’t post In wanted yet so can’t ask in right place. They seem to be as common as...

Thanks You’re right. The threaded plate was the problem. There’s two cavities. One OK. Empty. One tiny. At the bottom of that one is a traditional dog bone shaped plate. Head scratch. Right. Uncoil a wire coat hanger. Make tiny hook at end. Smear end in superglue gel. Let it go...

Hello. A newbie with a just new to me FL1. I have posted a hello in the intros thread, but have an almost immediate problem.... almost certainly self inflicted. My fiancée wanted the roof off. So, no problem..... remove roof bars. Take off roof. OK.... mounting brackets for the roof bars...