Search results

Ok, I'll try soonest I'll have access to the car. Remember it's 3rd world country, strange things can happen here with you. I cannot do this now. Anyway, it's possible that this switch is cutting of power from radio and ac? I were disconnecting radio already to make sure it's not it.

No

Yes, they do. As I said - temp gaue is maxed out and temp warning light is on. Radio and AC don't have power on it.

Bingo! I've exchanged thermostat last week. Mine old (wchich I were giving to mechanics as new one) were just housing! They removed thermostat itself! After exchange car don't overheat! Great thanks! Unfortunately car currently don't drive at all. During standing in traffic I was listening to...

Ok, I'll tell you - there's a dumb advice on this forum - to use 12v on the purple-blue cable. Don't do this! This will harm your CCU! It did to me, now need new CCU + reprogramming.

yes, they are turning on. Ok, Thermostat is easy to change, I've ordered it already, I want new owner not have at least this problem

Thank you! I really appreciate!

Thank you, I actually did that, but middle part of the cable is always covered and as you can see 4 pins from new design switch are connecting into 3 sockets of old socket. I didn't figured how to connect these cables. Additionally I've rechecked cables at the right side of the engine bay and...

Dear, I fixed my LR FR V6 after he 2 years he were not working, and I basically though that I stayed with 3 amigos and F4 error, but no... My tailgate stopped to open, I read on this forum to power blue-purple cable with 12v to force open the solenoid. In my case solenoid were good, just this...

I found another problem. It's overheating on idle. Ventilators work only on revs, but when it's idle and starts to overheat - no. What could be the problem?

After changing both front abs sensors i don't see change in behavior of the car. I believe I got same errors as mentioned previously. I'll do new reading when I'll see change in behavior or the car. I'm still using old brake switch, I don't know how to connect wires to new one. I've tried...

I'm sure error appears a good while before gearbox goes to the 4th gear, sometimes is even below 40 km/h (I observed yesterday) - even around 30 km/h. Once, after removing battery, and changing these abs sensors it started with Hdc only, and after while appear rest of the errors. I need to...

You think this could be 4th gear valve?

Yes, I went through this procedure, oil level is correct now. I believe I've added after drain and this procedure little less than 4 liters. I can go on 3rd to around 50 km, but it's already with error engaged.

Thank you @Hippo for your attention. Error appears on 3rd gear and after reaching 40 km/h. I'm not able to force it to switch to 4th gear before (probably gearbox ecu don't allow me to use 4th before 40km/h). After error comes, and car speed more I feel 4th and 5th gears are engaging. I don't...

Thank you, @Hippo i didn't saw your answer. After last post I did : Manual inspection of the wiring at the left side od the engine bay (this Going to the Abs sensor) - i didn't found any problem. I did also manual inspection of wiring going to the injectors and coils - in center area of engine...

Overall this car were in good condition when purchased, only ~90 000 miles done, and it were visible. I think it were tortured by heavy reving through... as I needed to exchange IRD as well after I've fixed the engine (VCU test went fine). The car was standing 2 years at different mechanics...

Yes Problem is I don't have quick access to the harness, which cost get sky high anyway. If there are only wires, I can connect them myself. I've tried following combination, but switch didn't worked like that (I'm attaching below). I believe my problem is fully electrical, as gearbox even...

Ok, I left this new brake switch as my old one looks working after cleaning - brake lights works. Till last time I've checked - gearbox cable that goes from gearbox ECU till barrels - looks fine. I've cleaned all ground cables, including this on gearbox, aswell sanded with sandpaper for better...

Do you know pinage of them? So far I found that pin 1 and 2 from New switch should be connected into the one, and go into the pin 3 into old connector. But that eventually blowed up my Fuse. Maybe combination is different? I cannot see all wiring, because connection part between new switch and...