Search results

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. M

    P38A reverse is crawling

    Checked all the wiring today.One cracked blue orange wire near the leverer switch ......still no reverse. I read in rave that if selenoids are not feeded there will be a fault warning on the display so there must be a leak somewher. I think it is getting time for looking for another auto box...
  2. M

    P38A reverse is crawling

    crawling very slow and not enough to go backwarts more than a few meters so almost nothing.On the display all shifts appear
  3. M

    P38A reverse is crawling

    When I go back to when the problem started after renewing the oil pump. The first test ride the reverse worked fine and when I used the reverse after 30 minutes the second time there was no reverse.........
  4. M

    P38A reverse is crawling

    It may be a wiring problem by not activating a selenoid or a leak somewhere as I understand
  5. M

    P38A reverse is crawling

    I mean valve block
  6. M

    P38A reverse is crawling

    I took the body block apart completely cleaned it checked the solenoids rebuild it .new filter oil........ still no reverse only a slight crawling.forward shifts go fine. I am almost sure I did everything to the book. What could be wrong ...broken ????????
  7. M

    P38A reverse is crawling

    i pulled it out and put it back together.again This can only be done the right way or the total it will not fit together.and you feel clearance I think the best way is to do the valve block job again and refil together with lucas 10009 and see what happens. Have good hope
  8. M

    P38A reverse is crawling

    I know .I have been thinking the last days what I could have done wrong .Fitting the oil pump went ok. New filter etc I have done often before.
  9. M

    P38A reverse is crawling

    reverse and all gears were fine before the job
  10. M

    P38A reverse is crawling

    new filter
  11. M

    P38A reverse is crawling

    oil is ok
  12. M

    P38A reverse is crawling

    I just checked the oil after a long testride and it was up to maximum stip
  13. M

    P38A reverse is crawling

    it makes no dfiference cold or warm. I made a longer testride today.I must say the box is not as smooth as it was before.The first three gears go rather well. the fourth gear is sticky
  14. M

    P38A reverse is crawling

    forward gears go excellent
  15. M

    P38A reverse is crawling

    I checked everything 5 times with rave.Fitting a new oil pump is not too difficult.The pump works fine.The starange thing is.......my first testride the reverse worked fine the second test ride after 2 hours the reverse started crawling
  16. M

    P38A reverse is crawling

    I hope nothing is damaged I did not pull the valve body apart
  17. M

    P38A reverse is crawling

    after changing the oil pump in my p38 zf24hp gearbox petrol and refitting the gearbox with new oil and filter the reverse is only crawling a bit. whatever I try with driving or shifting ,,,no luck....... Before the job everything was doing ok. would lucas fix help or is it just bad luck...
  18. M

    after changing starter ring aut gearbox does not shift p38 4.6hse 1994

    you are right I think the only reason can be in my case the pump lugs
  19. M

    after changing starter ring aut gearbox does not shift p38 4.6hse 1994

    can these pump lugs break just like that? And als both ? I do not know how strong they are. If the job is done do the errors on the display have to be erased by diagnostics
  20. M

    after changing starter ring aut gearbox does not shift p38 4.6hse 1994

    I thought there only is one possibility to click in the t conv into the pump otherwise the t conv will not fit to the ring gear of the starter and the bell housing will not close . I looked at clips on youtube how to fit a t converter
Back
Top