Search results

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. @

    Nylon bushes

    Thanks for the advice on both matters. Front shocks seem ok it just sits low at the back when towing. No leaks but feels bouncy.
  2. @

    Nylon bushes

    Hi im after some advise. I have several creaking noises on my td4 majority front end. I'm putting it down to 139000 miles and thinking of changing shocks and all bushes ect round suspension just to give it an overhaul as not sure when any of them been changed. Any recommedations welcome and...
  3. @

    1st gear ??

    Hi I have started finding it difficult to engage 1st gear. Really stiff to engage and got to really push it in. Had new clutch, slave and master cylinders fitted last year. Does clutch need blessing again?
  4. @

    Egr Blanking Mod

    Cheers yes have done.
  5. @

    Egr Blanking Mod

    Did my EGR valve mod at the weekend. Three cans of oven cleaner 1st can left over night. Could not believe the gunk that came out of the air box. Put all back together. Engine sounds better, sharper acceleration at low revs. Biggest thing I've noticed is fuel is lasting ages. Put 20 quid in...
  6. @

    For Sale 5 years worth of 2004 Freelander 1 TD4 parts…

    Hi how much delivered to Brighouse HD6 2LX
  7. @

    For Sale 5 years worth of 2004 Freelander 1 TD4 parts…

    Do you have rear passenger door window regulator both sides
  8. @

    Wigan to Brighouse

    Anyone traveling from Wigan to Brighouse need some kitchen unit doors bringing down
  9. @

    Egr Blanking Mod

    My HER seems really bloody tight into it' exhaust breather should it be if so what trick do you do to release
  10. @

    Advise needed - Engine keeps missing and very jecrky

    At last, what a struggle this has been but finally with the help of this site I have removed the tuning chip box and wiring loom. The chip was wired into the rail pressure sensor fortunatey the original plug was still on so it was an easy removal. Refitted boost sensor which has always been...
  11. @

    Advise needed - Engine keeps missing and very jecrky

    Hi going to strip it down tomorrow, so will report back and put full details on.
  12. @

    Advise needed - Engine keeps missing and very jecrky

    Hi I have opened the grey box I opened the grey tuning box up this morning inside is a very wet circuit board, it is covered in protective wax but I suspect water is the devil. Photos of inside gubbins attached. I'm very nervous about playing about with the settings, as i know little about...
  13. @

    Advise needed - Engine keeps missing and very jecrky

    I have messaged the eBay seller asking for an email of fitting instructions so I can then work backwards and remove this pile of ****e.
  14. @

    Advise needed - Engine keeps missing and very jecrky

    Hi thanks for the reply this is the exact unit and harness I have fitted on mine https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F202099697435 It is plugged into the fuel rail sensor and I believe the MAF sensor. The harnes on the link is exact to mine.
  15. @

    Advise needed - Engine keeps missing and very jecrky

    Hi got home and started car which I had running yesterday. Today hard to start lumpy and loads of black smoke followed by white smoke. It then died and would not start when it did it was only for seconds. Unplugged grey box. Car started straght away but engine management light stayed on and...
  16. @

    Advise needed - Engine keeps missing and very jecrky

    I think this has just been teed off the boost sensor has been disconnected and the vacuum pipe to EGR has been blanked off, EGR Valve still on vehicle which I am going to by pass. Its been running ok bit gutless when pulling weight but ran it for a year no major problems. This has been the...
  17. @

    Advise needed - Engine keeps missing and very jecrky

    Looking at the wiring it goes from the rail sensor to a MAF sensor and tees off to the tuning box, I will try unplugging it and see what happens.
  18. @

    Advise needed - Engine keeps missing and very jecrky

    Does anyone think it might be an injector fail. So far I have not done a leak test
  19. @

    Advise needed - Engine keeps missing and very jecrky

    Hi if I unplug the trick box will I need to plug that socket into something else or put a standard wiring loom on to the sensor.
Back
Top