Search results

hi all I'm fitting a discovery transfer box (lt230 I think ) to a defender 200/300tdi hybrid. The transfer box is electrical, I've removed the sensor and left with the square peg were the speedo cable should slot in. The cable square seems slightly big to fit in, is this normal and if that's...

Thanks Lynall for the reply, Yeah Ive done that, just my dash display (speedo, fuel, warning lights) connectors have been cut and there no corresponding wires in the loom to see where they attach too, does the display wiring get connected to the fuses or some were else? Many thanks greg

Hi guys Just looking for some advice on the wiring looms, I have put a 300tdi disco engine in a defender 200tdi with its wiring looms (chassis, dash/Fuse board etc). The battery connects to the starter motor and then the wires go to alternator/fuse board? Then off to the appropriate places...

Yeah I've heard people say about distortion, I just thought a new bulkhead would have been less likely compared to a repaired one :) sorry to hear about your bulkhead tho! Was.there much alteration to the tdci bulkhead though for the 200tdi dash/heaterbox etc? Many thanks greg

Hi guys. Doing a rebuild, got galvanized chassis and all new nuts bolts etc. The bulkhead I have has the usual rust spots (footwells, pillar feet, vents) and looking to buy a tdci bulkhead and getting galv dipped. So what's needed to get the 200tdi dash and engine bay components fitted to the...

Hi guys Looking to buy a 300tdi manual disco for parts (engine, axles, etc) as I'm rebuilding a defender. Doesn't need to be rust free or anything just decent engine etc. Local to north west/merseyside/cheshire many thanks greg

Bought it couple of months ago for 400 (as rebuilding a defender from scratch) and got it from a local wrecker in liverpool area, I'm gna have someone have a look at it before we start un bolting everything and take it back as he said it was a good runner, or swap it :)

OK so I'll check tapets, and i take it a compression test would also check for head gasket? Or any other signs, no bubbles in header tank, and no creamy oil. I just don't wanna strip engine down in case the wreckers wont take it back after messing with it etc. Thanks for the replies

If the valve caps are damaged, wouldn't the engine run rough/effect it? As the engine starts half a turn, sounds nice, no smoke etc. Many thanks

Thanks guys

Thanks for the replies. So james Martin, would I find out by doing a compression test to see if the piston rings (or whatever is causing it) is causing it? Or could something as simple as tapets be the cause?

Right, we cleaned the breather, makes no diffrence, we left the pipe going Into breather and we even left one of the pipes going turbo off and it still spits at a high rev, and leaks at the gasket (cam chest) but soon as we take the filler cap off (pipes reconnected) there no leak/spitting out...

Thanks for the reply guys, OK well clean the breather on the side this afternoon and make.sure the pipes are clean. So is there only 1 breather on the engine?, and is there any other points I shud clean /check in regards to ventilation? I'll send a photo of were the leak is, engine starts...

Hi there We've bought a 300tdi engine for a defender from a land rover breakers. We fired it up and sounded really good considering it hadn't been used for over 6 months. But we noticed it had a oil leak were the block meets on the timing belt assembly (not the timing belt cover gasket if that...

I believe the gasket Thats leaking is the timing chest gasket

Hi there We've bought a 300tdi engine for a defender from a land rover breakers. We fired it up and sounded really good considering it hadn't been used for over 6 months. But we noticed it had a oil leak were the block meets on the timing belt assembly (not the timing belt cover gasket if that...

hi everyone, I'm currently re building a defender 90 pickup from the ground up. I bought a 200tdi chassis (galvanised) that has had 300tdi engine mounts welded to it (before being dipped ). It's at the stage of a rolling chassis, and now ready to lift the 300tdi/r380/transfer box (not sure...

Yeah very good point waldamar thanks, I'm gna strip it down to the chassis and build back up and go over everything and what's not good me and my dad will replace, but try keep it as original as. to some it might be a lost cause but it's me dads old series so like lighthouse mentioned it's a bit...

1500 sheets? Jeez good job ya used someone's else printer lol, I take it hey were a pretty detailed manual? Yeah that be great if ya could flick the links over to us when ever ya get a chance :D thanks lord of war

Ok so on the 1st and 2nd gear there no synchro, how's that affect the drive (never driven an old series ) Yeah I know tell me about it, lol it's a bit of a rough badge up job apparently.