Search results

I have rebuilt my series 3. But the engine is a metric 5mb 2.25 petrol. I have put 20/50 oil in. But have been told it should be 15/40? Anyone enlighten me please

Hi all can anyone tell me ERC 9448 Cylinder head blanking bolt what size thread is it?

Hi folks I need a part number for a 1985 land rover petrol engine serial number 63506336c. Believed to be military 2.25lt I need a starter motor for it. I tried putting my series 3 starter motor on but the spacing between the studs is wider on the 1985 engine. Thanks

hi folks fitting a Weber 32/34 DMTL carburettor to my series 3 landy. posted earlier on this but now having got all the studs out of the old manifold with no snaps/breakages. it is now a bit clearer, everything is metric but will still bolt onto series head and if i buy a complete 90 exhaust it...

hi folks i have a differential fitted to my s3 rear axle with no fill hole and none in the diff pan either so i have been filling it through the breather hole. now though needs a new pinion oil seal. it has 47 teeth on the crown wheel so a 4.71 diff and is a 10 spline. so which oil seal do i get...

my cylinder head is mark with the numerals Y2 adjacent to the center head bolt opposit the carb. cylinder head number is dupoint 525183 can anyone help identify which head this is 8:1 or 7:1 thanks

simple question!? can the steering box on a S3 be removed without taking off the drop arm. as mine is on solid and needs to be put in a vice. is it a complete wing off job? i have to work in the street outside so need to do it right the first time thanks to all

Ok found this under the engine after i had been tightening up the exhaust bracket somust have been knock off the engine block. Have googled to no avail has anyone got some info please.

Ok found this under the engine after i had been tightening up the exhaust bracket so must have been knock off the engine block. Have googled to no avail has anyone got some info please.

has anyone used these guys i have just posted the address on another forum but have not delt with them myself? http://www.automotivecomp.com/landrover_perf.html

changed my tyres to 235 x 85 - 16 on a S3 SWB in November last year much better ride and a few inches higher. only the speedometer was not reading correctly if fact it was reading slower than i was actually going which is ilegal by the way. so, i needed a new speedo down fom a 1536 to a 1408...

changed my tyres to 235 x 85 - 16 on a S3 SWB in November last year much better ride and a few inches higher. only the speedometer was not reading correctly if fact it was reading slower than i was actually going which is ilegal by the way. so, i needed a new speedo down fom a 1536 to a 1408...

i am about to rebuild a gearbox and came across this. is anyone using or had one of these a ashcroft High Ratio Transfer Case Kit fitted to their S3. http://www.ashcroft-transmissions.co.uk/the-series-vehicle/high-ratio-transfer-case-kit.html are they any good? did they make much of a...

Member Joined: Aug 18, 2014 Posts: 29 Likes Received: 3 Location: kendal just changed the clutch slave cylinder on my s3 only for the master cylinder to go as well on bleeding it. so.... off with the master cylinder 2 bolts what could possibly go wrong! well i'll tell you the bottom bolt is not...

just changed the clutch slave cylinder on my s3 only for the master cylinder to go as well on bleeding it. so.... off with the master cylinder 2 bolts what could possibly go wrong! well i'll tell you the bottom bolt is not as i have found out, not a fixed stud and has probably been the there for...

i need a new heater unit in my S3 and http://www.t7design.co.uk/ seem to have whats needed. so has anyone fitted one of these in there landy http://www.ebay.co.uk/itm/3-5kw-Lightweight-Heater-for-Mini-Land-Rover-S1-2-Kit-Car-Westfield-Cobra-/190983218231

hi folks just done a oil change on my S3 gearbox and this came out see pics would anyone know what it is? it has broken in the middle as the break on both match. i think it has come out of the transfer box with more oil than should have been in there so oil seal needed as well. cheers

from paddocks spares - Intertia Lap and Diagonal Belt for outer front seats of Series hardtop vehicles. Brand: Securon £23.14 Ex VAT Inc. VAT: £27.77 Part Number SEC50030 opened the box and read the intuctions.... this seat belt has to be fitted in a vertical position only or it does not...

hi folks anyone out there know which cable fitting goes on the back of this speedometer "Series 3 RTC5035 Speedometer " for 750x16 tyres.-- is it screw on or clip/push on. i can't find any pictures of the back of one anywhere on the net. cheers

found this link hope its of use to you all. just fixing the speedo in my s3 as it is not reading right with my new 235x85x16 tyres http://www.tr3a.info/PDFs/speedo.pdf