Search results

Hi Chaps need some help regards terrafirma heavy duty rear springs.I believe these are fjtted with the tighter coils sitting uppermost but for the life of me i cannot tell the difference. What i have noticed on the bottom of ea ch spring there is a notched piece right on the end.Can anyone tell...

Hi Guy's Looking for a few tips on jacking up the disco on my drive.Struggled today to get enough articulation on the front to get it to drop enough. I have a good trolley jack and 4 stands. Any recomme dations on jacking greatly appreciated...

Just took the two spaniels to the vets and noticed a prominent clicking coming form the gearbox which only happens when i down shift from 5th to 4th. Sounds expensive,any ideas:confused:

Hi Chaps Started to hear a loud buzzing from the engine bay and discovered it was coming from the Egr module. I have blanked off the Egr valve so is this module still required? If so will it be a replacement unit,more cash:confused:

Can anyone tell me if it is normal for the housing around the fuel filter to get hot. I did slightly over spray with waxoyl but have now cleaned it off Any thoughts?

Well i have just completed my Ace removal and I am happy with the results. The vehicle is due an mot on Tuesday but as a result of replacing the system the amber ace light is visible,my question is will this impede the mot or is there a way to remove the light other than using a diagnostic tool...

Can anyone tell me the correct torque setting for the bolt that connects the idler pulley to the bracket-Ace pump replacement.

Hi chaps Can anyone tell me the part number or bolt required to attach the anti roll bar bracket to the chassis please. I am in the process of removing the old Ace system and have lost the 2 bloody bolts. Cheers:)

Hi chaps Decided to replace my wheel arch mouldings today in preperation for my new terrafirma replacements. On closer inspection I noticed some corrosion at the bottom of the wheel arch. Would it be advisable to cut this out and treat it as the new mouldings will hide it. If so can anyone...

Hi chaps Can anyone recommend a retailer to provide a quality kit so that i can replace my ace and install anti roll bars,drop links and pulley/belt to replace pump cheers mark:)

Hi guys The dreaded ace pipes are leaking so i am looking to buy a kit to replace the lot and fit roll bars. being a fairly competent diy mechanic does anyone know for a step by step otherwise its gonna cost £250.00 which i cant really afford cheers chaps Mark:)

Hi I have recently converted to coil springs on my disco 2.Does it make a difference as to what side each spring goes on ie left and right,if so how can you tell?

Can anyone tell me if these units can disengage the air suspension once you have changed to coils thanks:)

Hi Chaps I would like to change my pas/ace fluid but have not got a clue how to drain and replace.Can anyone point me in the right direction please, step by step etc Thank you:o

I have just removed my rear suspension and installed coils.I took in on a test drive and all seems okay but I was expecting a warning light as the air suspension had been disconnected but no warning light any ideas?

Servicing the Disco today and got round to replacing the fuel filter and noticed that the pin that connects into the bottom of the filter had been disconnected and tied up with some tape.Anyone know why this would have been done?..

Guys popped out to start the disco 2 tonight after standing for. 2 weeks and noticed the rear suspension really low compared to the front,any suggestions I am thinking air suspension issues:(

Guys I have been trying to do some maintenance on my recently purchased Disco 2 to save a few quid. I have changed all the pads and disks and am now moving on to replacing the oils and filters. I have run into a problem trying to remove the engine sump bolt - it's bloody solid and me swinging...

Firstly happy new year to everyone. I had a bit of a nightmare today replacing the seized pistons on the rear of my disco. I damaged the new seals trying to push the piston in and i ended up pulling my hair out and i am follicaly challenged as it is. Can anyone suggest a way of inserting the...

Hi Can anyone recommend a good supplier of spares and servicing bits and bobs Oil,filters etc. Also need to fit new pads and disks Thank you Mark.