Search results

the dvla advise that you wait 6 weeks after they recieve your application before contacting them, proof of posting and with tracking from a post office counter is a must for anything that goes to SA99 1BA. if you contact them before the 6 weeks you just get told to wait til the 6 weeks from...

Perhaps new shoes pushing the brake pistons in and pressurising the brakefluid, perhaps undo a bleed nipple to take some pressure off, beating around the outside of the drum with a rubber mallet sometimes helps, Atb and good luck

Is the hose sucking?

You write 'Set up', is it fitted as standard or retro fitted, is your land rover diesel or petrol?, if you post some more background i'm sure you will get the info to get it working, Atb

Put it level with the square drive in a vice and hang a known weight off of it at 1ft along the handle, if it clicks then its right, there are plenty of guides on the internet for diy calibration,

Ive got a working tranny 2.5di pre banana engine with manifold,pump and a milner plate and adapted engine mount taken out of a series 3, £500 and can deliver to Plymouth ferryport if paid for up front, Not a 2.25 but could get you mobile,

If you are the type of person that would nick somebodies pride and joy then i rekon you may know where to get plates, A corner shop that sells vapes and phone accesories up the road from me has recently started selling laminated 'show plates' for £20 each, not for road use of course, Perhaps...

My mot garage will make up a single line inc the correct fittings for self fitting, the last time a couple of years ago it was a tenner,

Got tired of trying to give somebody some work so did it myself,

I have noticed that the new petrol doesnt even smell strongly like petrol after a while, i like my bikes and my day to day hack is an xr250, with the new fuel it is a sod to start when cold and much lumpier, the power/mpg is down, this was noticable when both types of fuel were available and i...

i have previously had a 88 with a lead free head, it was fairly thirsty and with the amount of miles i was doing combined with the documented problems with the 'e' petrol going off in petrol tanks,there are no petrol stations anywhere near me selling the older type of petrol so i was having to...

Anybody know if or can recommend a land rover series savvy mobile welder in west cornwall, Thanks Ryn

Welcome,re the ulez, to be quite frank i think getting a109 into a parking space in london traffic is not something i would look forward to, Atb

I couldnt upload the pics here but i have put them on lruk and will try to get them on here and a few more progress pics if i get access to a laptop

Thats just about how i was planning to go forward, the right hand pillar has to be done for the structural integrity so thats first, tbh its so bad that i wouldnt drive it without it being done and then i will most likely just cut out the rust and weld a 'do for now' plate over the wiper...

Thanks for the replies and info, i have used the links and have bought pillars,feet and repair panels from yrm, my 2a 109 has very severe but localised rot, mostly the footwells,tunnel,dash compartments and vents etc are all in very good condition and have never been welded, this '69 109 station...

Does anybody know wether the carawagon and sixpot association is still about,

I am weighing up my options as to wether to repair my bulkhead which is surprisingly good apart from a few areas on the right and left sides where it is completely rotten or to buy new, Any pointers to the best supplier and also the cheapest supplier would be most welcome, i am more leaning...

Thanks for the offer, it is appreciated, when my next renewel comes round i will contact you in good time.

Any recommendations for an insurance company for the above with a manned phone line, previously with my 88 i got tired of listening to music for 1/2 an hour on flux's customer service number and went with gallaghers via quoteline but atm i cannot buy online as they dont recognise my reg, Thanks