Search results

Mine: 1. Main beam selection goes via relay hooked to cigar socket so that I cant leave full.beam on and flatten the battery 2. Solar panel wired into LH rear wiring ( not much use for UK) but I use it for a fridge too 3. cigar socket replaced by USB and voltmeter 4. Eka and immob disabled 5...

safety first...attempting to stopping a 20+ yo piece of rotating plastic running @ 100 mph+ at the outer edge may not turn out so well. Had i done this newspaper test the day before my fan failed i probably would have been seriously injured at worst, or caused further distress to the fan blades...

if you had ever suffered catastrophic failure of the fan blades (and it's pretty common) you would be less keen to stick things in the fan

I have only had 98s, no relay, although I retrofitted a relay harness to one. But I agree, more likely blend motor's.... Feyniriel, Nano v useful for diagnosing because you can " watch" the blend flap percentages change as you press the buttons on the hevac. One or other will likely not read 0...

First question is, if you start up with the ac off/ button pressed, turn the ignition to II ( and no engine) how long does the book symbol take to come on, if at all...If no symbol then prob blend motors are ok...engine on now, set to Lo, ac switch unlit (ie on), do you the book symbol after a...

actually the biggest PITA for me was removing the bolts holding the radius arms to the axle... tip for the top, if your bolts are rusted in get a hammer action SDS bit on the end of the bolt and you can drive the bolt out in seconds. To stop the chisel walking you can put the old nut on a few...

The fella being me : o) although no doubt there are others. Sorry, rubbish sound... You're going to need a 30306 taper bearing race and a standard bearing puller kit with some jubilee clips and big washers. I'd already done the arms by this stage so filmed the vid using a mock up Please...

I guess you will soon be eligible for a frequent posters card on here : o) They way i did it was to initially remove the grille, you may have to snap the plastic tabs at the top retaining screws. then you will have restricted access to the underside of left and right hand locks - you need to...

Personally I have never removed the bleed hose on mine and never had any probs. As already mentioned milk the top hose and get the blled hose "weeing back into the reservoir at decent revs. Monkey, I think the prob on your procedure is "taking car that the level does not drop below Low" which...

You can follow on nano

yes, if you undo the round connector all you need is a 9v battery across the two connectors to pull the clutch in. I suppose that with no book symbol you will probably be fine. I'd just go ahead and get it refilled. They shd vacuum test it before refilling anyway. Once they have refilled it...

Unfortunately it doesn't, all you can see in Nano is AC request and AC grant

I'm guessing you cd also buy a longer rubber piece. If you put heat or an induction loop on the exhaust bracket then you may be able to close the gap a bit

Fair enough - i might have been imagining it/ going slow enough around the multi storey car park that it did not rise... I will be more careful next time : o)

Yes I agree. The p38 I bought recently had had a full respray, and they have obv removed the c pillar plastic and resprayed

How far do you need to drop? I had a few ideas but now not sure any wd work...but perhaps you cd use a bracket to lower the receiver mounting itself a couple of inches, rather than do anything to the swan neck

The two yellow ones plug together, no?

But after lowering you use the suspension lock button... It can be a bit uncomfortable going over the little ramps on bump stops is all

I heard that putting a pencil sharpener on the end of the line to cut an angle on the end of the pipe cd help bed in the connection. Worth a try if you have exhausted all other options

When you say eka not clearing faults...are you following the door lock procedure, or using hawkeye? Is your eka defo correct? Does the car acknowledge the correct code?