Search results

Both origional. Have a set of after market ones (one britpart and other 4x4something) which I had installed when I lifted the hippo bit removed them shortly after due to issues i had with them. Still have them and outer cvs fit the origional ones which I can use in case i need to replace cv. But...

Looks fine. Just barely moves in and out a little normal like all other shafts.

I have replaced all front bushes on mine to polybush so not them. mine does it when pulling up slightly harder than usual on full lock to the left. thhink I will be installing a small camera facing the suspention and drive shaft and see If I can see any movement compatable with the sound...

have a similar issue. did you find out what it was? no noises when driving. but when pulling up hard from steady at full rock to the left. I hear a clank or 2 slightly loud from front underneath the car everything on the suspension looks solid and no wear. recently had a split boot on the...

could be but still can't understant why it workd again but the other way round.

Small update. Went to work on it after work ....aaannnd....... everything works again efore even doing anything. But When I press up, window goes down, and when I press down, window goes up. I did re wind the cable when I replaced the motor but I'm 99% sure I did it cotroctly as it was before...

I have a spare fusebox i ca n try. are they a direct replacement or are there different ones? Any one tried it before?

Looking again. The window relays are in the fusebox. 2 for each window. May be able to replace them if individual as I have a spare one. But will have to look into them again.

@Nodge68 helps a lot. From what I can seeits the ccu that switches the polarity of the cables to control the windows so probbably that's at fault. Will check it out. Thank you.

Can someone post a circuit diagram for the electric windows here or send one on my email address [email protected]? One from a hynes manual will do. Freelander td4 5dr.

Checked the lock switch in the center console and now both work but again only one way. (Down) tried the switch from the other door and same thing. So fault is elsewhere.

Hmm. Wireing in the door look intact and no damage. Ccu is my main suspect. Only two wires go to the motor so my guess is that the polarity of those is switched inside the ccu unless there is some kind of relay for every window somewhere.

Today's problem: One of tge back windows will only go down and not going down from armrest switch. door switch not doing anything. Tried another motor and does the same. Checked voltage on motor connector and when pressing down from armrest switch there is a voltage reading. When pressing up...

50mm lift by muddymods. modified the inner wings. (1 cut on each side and then one horixzontal along the chassis and a friend of mine welded the seam although 2 vertical cuts and bending the metal down woud have worked also) didn't swap the steering arms but that would have helped a bit more...

something will probbably give you some hard time but other than that, it's simple :P

I suddest you 1st try to crack loose the bottom bolts on the shock. they are the worst in the whole process and the most time consuming. try spraying wd40 or some penetrating oil and cleaning the exposed threads with a wirebrush from a couple of days before. It will help. also as I sid go trough...

ok so. remove the wheel and open the hood. you should be able to see what needs removing and undoing. Its pretty streight forward and more or less accessable by moving thinds to the side. as for the back you need to remove the boot side trim panels which is easy enough. try inspecting your setup...

Those Re the mounts I would like some pics of. Esp the back ones. From the pic it seems that there is a "block" spacer whick mounts in the recess where the rails mounts and then the legs mount on top of them. But couldn't find one of the rear ones. They are crazy expensive and if i find one...

On the one I have I got a pair of used roof rails and cut the bases and used them and have been fine since and also strong. But am looking to make another one from scratch and was woundering if I could use something else for the mounts that's less eyesore. This is my current setup:

Does any one have a G4 roof rack on their FL1s that can post some pics of mounting points? or for those who built their own roof rack, can you post photos of how you mounted them on your roof or of mountings used to mount on existing mounting points? Planning on making my own but still un...