Search results

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. ProcrastinatorFraser

    Hydraulic press build

    I have a 10 ton and a 20 ton jack lying around.... I've decided to make a press, after using one at a garage (huge 50 ton beast). I shall be passing by the old metal shop later today, and i'll hopefully get to work this afternoon.
  2. ProcrastinatorFraser

    Caster Corrected Arms for early 90

    I haven't done any lifts personally, but it sounds to me as if it accommodates the radius arms from a discovery or older defender. My 86 90 front radius arms were probably about 5-10mm shorter than the disco ones, but only on the bracket you have the 4 bolts that go on the axle, if you see what...
  3. ProcrastinatorFraser

    Splash guards for series landrovers

    Thanks, i'll look in to them ;)
  4. ProcrastinatorFraser

    Splash guards for series landrovers

    What tires are you runnin? I like the looks of them...
  5. ProcrastinatorFraser

    Series 3 1977

    Started painting the old leaf springs, just until i can afford some proper parabolic springs, but they are not the 1st thing on my shopping list. Got a paddock order in, everything i need to get the front and rear axles restored! Been doing some other stuff in preparation. 1 rear leaf...
  6. ProcrastinatorFraser

    Towing

    Right, so my X member is a replacement unit, but i think the bent X member may have been badly corroded to have bent the way it did... it was very bad, it's a shame i didn't take a picture of it!
  7. ProcrastinatorFraser

    Towing

    Once restored, my series 3 might be doing some light towing and stuff like that, but when i went to see a guy about tires, the cross member on his series 2 it was completely bent backwards because he had been doing snatching/towing around his yard. I do NOT want that happening to mine, what are...
  8. ProcrastinatorFraser

    110 Rear final drive swap options

    What makes you think it's the diff? what evidence is there as to it being the diff?
  9. ProcrastinatorFraser

    Series 3 1977

    Picked up an axle yesterday.... it wasn't complete, but i got some halfshafts and other various useful parts from it, final drive unit and everything. The casing is in really good condition, even though i had already painted the other one, this looks in better condition so i'm going to use that...
  10. ProcrastinatorFraser

    Series 2

    Is it anything similar to what i was getting here?
  11. ProcrastinatorFraser

    Series 2

    Well i had a very similar problem when i tried to get my series 3 diesel to start, it's most likely going to be air in the fuel lines. In my case, i kept cranking it over until it fired and cleared the air in the system, though there are ways of bleeding the system out which are a bit more...
  12. ProcrastinatorFraser

    Series 2

    by the looks a diesel engine, i'm assuming?
  13. ProcrastinatorFraser

    Series 2

    Series 2... petrol or diesel engine? would be good to know...
  14. ProcrastinatorFraser

    Series 3 1977

    Thought i would carry on posting on the ORIGINAL restoration fred, instead of starting a newen all the time. Should get some parts ordered reasonably soon to make it a rolling chassis again, it's been a while since i was able to push a chassis around instead of carrying it everywhere...
  15. ProcrastinatorFraser

    Gearbox issues

    Cos that's how life works with a tratter :D
  16. ProcrastinatorFraser

    Gearbox issues

    Well, bollocks. :D I may have to improvise the way it was before..
  17. ProcrastinatorFraser

    Gearbox issues

    well i got f6-5 stamped on the selector casing but nowt on the gearbox
  18. ProcrastinatorFraser

    Gearbox issues

    I will check them...
  19. ProcrastinatorFraser

    Gearbox issues

    Well i got me a mismatched pair then, when i took the selector top off, there was a copper spacer in between the 2 pieces, if it wasn't there, the selector shafts would bind between the 2 casings
  20. ProcrastinatorFraser

    Series 1 Porn

    Christ knows! i don't know who would be willing to pay that money for it..
Back
Top