Search results

I was wrong - the Haines Manual says starter and inlet manifold out It's been 38 C here - I am not looking forward to doing this :D Rover 75 / MG ZT CDTi (Diesel) Engine Oil Cooler - PBC101370...

Sod it, it appears really hard to get hold of here so I ordered one from Island 4x4 too to have a spare

Done, Ordered from UK to deliver to mum's I went for the 50 quid one from DMGRS In case anyone else has problems ordering online from them as well, I could only get it to work by using the Paypal button on the screenshot below. Clicking the CHECKOUT button didnt work, neither for the...

Thanks I think that @Arctic2 's last link uses the part number to make in non-vehicle-specific? Although I knew it was a BMW, I didnt know the td4 was a M47R, it was the 185 HP? https://en.wikipedia.org/wiki/BMW_M47#M47TUD20

The only Europe ones of interest I can see from @Arctic2 's google linkare these: Germany AllBrit OEM €106 But 'O' Ring and not gasket? https://allbrit.de/epc.cfm?CAR=L6&SPRACHE=EN&PAGE=G03105 France (?) RLD Autos OEM €150...

Oh! I managed to miss the third link - thanks!

But ..... Motormaquina can only get Britpart from UK, so with customs its 200 quid (probably plus 23% VAT - I didnt ask) Bugger! Welcome to my 'relaxed' life in the Sun :cool:

Apparently this is the place here in Portugal https://www.motormaquina.com/ For anyone breaking down near Lisbon or Porto (or elsewhere in PT) And a great Freelander specialist just south of here is Nuno Sousa who is a great guy and a great mechanic - contacts and translations on request : )

Thanks I completely understand just using this as a comparative test - I was just curious I did my own spreadsheet: analysis from the data from around your link If speed was simply proportional to the torque the power of x in the below would have been -1, but its not. Interestingly (for a geek...

Thanks, that is cheaper than I imagined but coming from UK means PT customs who are W@nkers Anyone coming to Lisbon soon for holidays? :)

Thanks! The Haines FL book says take out starter and radiator but looking at it I am not sure if necessary. I am probably wrong. I will try and cost/source a new cooler anyone got any advice on where and where not to try to buy? I am in PT so post Brexit, Europe (inc Ireland) and not UK is best...

Mine is Manuel

Not my area, but I would take the comma out as then its clearer that all three methods all apply to the trigonal oxygen site etc and not just transition intensity modelling. Whatever the **** they are However, Oxford commas are always a bit of a moot point If I were him I would leave it in and...

You'd have to plot 1/time as that equation has N which is revs That equation makes sense, as you increase weight &/or lever arm, the speed of rotation (N) increases and so the time to do 1/4 of a revolution decreases. The equation also tells us that 1/time should vary linearly with length &/or...

Hi! Has anyone tried tests to see how the time varies with weight and lever arm length? From this it seems that Revs/min is simply proportional to torque (weight x lever arm) I know its not the same geometry, but its an 'engineering' equivalent system and everyone's VCU is the same...

Hi, 2001 FL1 Td4 I have had a bit of oil in the water for a while but no overheating or steam or smoke in exhaust, temp fine (even in 30 + C Portugal weather) or anything suchlike. But suddenly the temp gauge was creeping up to halfway, which wasn't that alarming but higher than normal and so...

@Nodge68 tried to send message but would not let me

GGreat! Thanks. Will send message with address etc

Thanks both I'm actually in uk near Colchester at the mo. How much fluid do I need and how much for me to take that off of your hands @Nodge68 ?

1. Laziness 2. Lack of money 3. Being Portugal lack of access to materials, especially the silicon fluid in VCU