Search results

ELECTRONIC AIR SUSPENSION AIR COMPRESSOR Service repair no - 60.50.10 Remove WARNING: The air suspension is pressurised to 10 bar (150 lbf/in 2 ) . Dirt or grease must not enter the system. Wear hand, ear and eye safety standard protection when servicing system. 1. Depressurise system...

Sounds like the pump has gone, had this fault on a friends one and is was the pump. You cant just replace the pump and drive away you have to have the system reset to allow it to work again properly. If your from kent/SElondon way theres a mobile RR guy from Faversham that can reset it for u...

Also found these on the rear arm, they look like they are ment to be split bushes as the rear suspension passes through them, but if some one can confirm this for me thanks

I have measured the hub and inside of the wheel and both measure 70mm so not the rings. i got the thing up in the air last week and have now found the front left radius arm bush split. (Pic attached) This bush wasn't split before so i think this is the clonk but not convinced it is the cause of...

Hi got simalar problem on mine, a few people suggestest the engine and gearbox mounts, might be worth checking them first

Thanks COOL CRUISER, i put new shocks put on it at the beginning of december and it wasn't that. I know what you mean about the car pulling across the road mine does it now and again i just assumed it was because it had fat tyres and was catching ruts in the road. I'll try and borrow a set...

Hi thanks, i'm sure when i was doing the discs and pads i checked that as someone else suggested that too me too, i'm sure it was fine but i'll double check on monday to be sure

Evening, I had the car up in the air today and theres nothing wrong with the engine and box mounts. Didnt get time to do hubs and everything else, however when i drove it to pick up missus i now can hear a heavy clunk when turning left, which i felt through the steering wheel and shaking...

actually you prob wont see the towbar from there.

Is there enough space at the top the tailgate where the rear wiper sits? pehaps in 1 corner and run the wiring with the wiper motor wiring, just a thought.

my mates got a mobile tyre bussiness might try and get him out of bed tmw then haha

Thanks i'll try and see if there's any movement in it, better have about 20 weetabix in the morning!

I had the balancing done at 3 diff place's makes no diiference, Would balancing show up an out of shape tyre? I have heard of tyres coming apart from the inside but no idea how to spot this.

it's been there since i bought it, felt like it had lost a wheel weight and i found one on the drive where i bought it from so wasn't too worried, til i got the wheels balanced and the problem continued. Its odd some times it feels like its in the back and other times the steering wheel is...

I'm with you, yer the wheels have a 70.1mm centre bore the same as the P38 hub no need for the rings, wheels cant be genuine L322 then!?! Thought you ment the preload shims.

mine was doing this I put in new batteries and adjusted the tension on the battery inside the remote and it still did it, i then cleaned the negative pole on the car battery and problem was gone.

You could weld a small plate/box onto the tow bar itself and mount it in that, you can position it at the angle you want and add a sunsheld which you'll need unless it's a good camera.

Hi thanks for reply, got the later wheel nuts with the wheels, dont no about the location shims only started reading up on them 20 mins ago, i'm down the workshop tmw i'll get it up in the air and have a look, is there any way to check they are adjusted right? if they're on it. (2000 model...

now thats a head turner!!! HAHA!!

Hi and Thanks for reading. I have a p38 2.5dt and it shakes like crazy from about 50mph, it's got 20 inch RR wheels on it. I have already put new discs, pads, panard rod bushes, shocks, steering damper and checked for play in bearings, hubs, cv joints, uj's and there is no noticable play even...