Search results

Ok - so it should be down then, thanks !

Ok - thanks man ! Can the inertia switch only be pressed when the key is 'on' or first position ? Mine is very hard and doesn't seem to move there's no reason why it should be tripped but it is solid and worth investigating.... Only other thing i can think off is 'ice prop' if condensation or...

Didn't replace the coils. Can hear whirring in the back but its from the charcoal/gas petrol cylinder under the right back wheel - gonna have help to listen to fuel pump tonight - shouldn't i get a code or engine light for fuel pump though ? There is no fuse anywhere to check right ? Regards...

Hi again Nodge ! Advice needed and appreciated! Freelander 1 1.8L k-series Facelift 2005. Starts up with start gas sprayed in air intake then dies - otherwise turns over but won't start! New sparks last summer. Full power in battery. Can it be its not getting petrol ? Would that be petrol filter...

Hi there ! Freelander 1 1.8L k-series Facelift 2005. Starts up with start gas sprayed in air intake then dies - otherwise turns over but won't start! New sparks last summer. Full power in battery. Can it be its not getting petrol ? Would that be petrol filter or pump ? Inertia switch? No engine...

Ha ha ha ! Oops !

Ok - cheers! When i replaces the spark plugs i saw and cleaned a sensor on the front top left if facing the engine - thought it was the oil - taking it off to clean it, you could see down in..... its a puzzle aright!

The oil temp does go up as the engine is used then goes down when off. This is still a default thing ? Isn't there a sensor in the top head gasket? So its not for oil ?

Thanks! I still have the fan malfunction code though - P0480 - they will never come on till that is fixed... Is it normal for the oil temp to reach 123 degrees c ? Cheers!

Do you have a picture of the part and a location diagram for it ? Thanks! Have cancelled the trip for today - we're nervous about it . I'm 50 today but its not worth risking the car just to fan my vanity.

Ok. You mean coolant sensor temp which is 92 doesn't reach 120 c ? This is also why no check engine light or needle going to red, even though INLET says 120 c. Habe to drive for a few hours tomorrow - keep the eyes on the guage .....i guess. Thanks again, really appreachiate your time and help.

So is it not safe to drive? Shouldn't it be boiling? I have 50/50 mix for rhe coming winter. Fans don't come on but have power etc - think ECM is up the left ? What would be next step - shouldn't i feel something when driving ? Regards, Arnodafe72

Drove the car 60kms - ECM computer coolant inlet temp said 122 degrees c - but coolant temp sensor on computer said 93 degrees c. Needle in dash was normal. There was no bubbling or steam in the pressure tank. If i didn't have the computer hooked up which gives an INLET temp, i wouldn't think...

Hi agin! New thermostat fitted new coolant after flush - temp on dash is still the same (normal), and the coolant temp on the computer is fine - but still the ECM coolant temp is at 114c to 117c - even with just short drive. The temp in the dash still doesn't go to red even though the ecm...

Yeah, mine never come on....also with the fans jumped to go all the time, the temp still sits at 112 degrees c , so things are also not circulating..... Thanks for the reply.

Ok! Super - let's hope its that - thanks again !

Having hot wired my fans to stay on constantly, i drove the car with the laptop connected to view the temp. Still reaching 112 - 114 c . This means either my thermostat is locked 'closed' and not allowing flow, or my radiator is clogged not llowing flow or my water pump isn't running right? Do...

Hmmm...

Yeah, if i disconnect the signal wire the fans run on the 12 v current - any idea where the signal wire goes ? Also , it has nothing to do with my AC , if there's nothing in it ? Also IMPORTANT: when checking the fan motors on the new secondhand fan rack i accodently attached the battery to the...

Tried the new fan rack - niether the ones i have or these start when the 2 thin wires are not connected (as was mentioned earlier as a safety feature). Tried new (secondhand) module - same results as my own. Tried connecting only the thin pink/brown cable (which has 12V constant) to its position...