Seaswood's latest activity

I did look for that on Ashcroft did not find it? Also checked the fiche there is a seal & mud shield there. Thnx

Is the transfer case rear seal transmission brake same as front seal? Seems I needed to fit a sleeve on the front transfer case output flange to stop the leak a few years back. It is a 22 DC can you tell ratio’s from other numbers or where would...

I have purchased a full set of fuel lines & the one odd spot is what you are referring to. When I get frame painted I am assuming I will have same question.

Everything already removed slave still in place as is old bulkhead, will have to wait until replacement of bulkhead.

Thnx this set up has been run around the lot but that is all. Replacing bulkhead as door sills were welded to original. Replacement bulkhead is a TD5. Torque meaning clutch not fully releasing I am assuming.

56A0144575 F I thought it was a lt77 came out of a 110 5door, I had it rebuilt. Installed with likely original clutch master, all removed to remove bulkhead. When reinstalled have a rebuilt unit from other truck. So maybe hew parts better...

Thnx I was thinking I needed to remove the shifter mechanism from transfer box as you said. Then I was wondering about wheels propshafts, undo propshafts probably best way to go as you said. The shifter arms are simple but will see. It does move...

Should you need to turn the prop wheels to engage the H/L diff lock? When all this was installed just trying to get installed & trucked home back in shed. So I will try to verify the levers this week. There was a series clutch on this truck I...

1984 110 PU when I got it had a defender 200 tdi determined head was shot still cannot remove the injectors? Lack of Maintenance one of the cylinders was leaking water. Transmission was a Sub D transfer was 12D004836A Replaced engine with a disco...

I had the injector bodies loosen up & leak on the 2.5 just check the injector bodies with a wrench ascertain they are tight.

Hot water & a brush

I am in the the New England, shipping required.

The screen is installed from the outside, seal goes on the windscreen first.

After cutting off the inside of seal the frame just dropped out of frame. I thought the Xmod frames had an internal interference strip in the frame, did not have a photo. Eventually when I get around to painting the frame.

That I believe is the adjustment on the master. Also depends on who made master how easy to adjust. Nuts on each side forget which way, likely make it longer delays engagement.

I have that tool likely last year Replaced glass gasket on sunroom large pieces of glass rubber gasket with expanding strip, like the rear windows on truck almost. Tool was semi hard plastic. I likely will get the LandRover gasket. All of which...

Probably my mistake was trying to push out from inside I am assuming. The frame will be repainted when warm weather arrives eventually. & assuming glass new seal wold be installed from inside, will be warm after this is painted.

Removing glass from windscreen, last time I did this I got a shattered piece of glass. Trying not to repeat that again is there a good vid on the procedure? I have looked not finding. A line wrapped around the seal twice but devil being in the...

Screw driver worked, next accelerometer I did need to get wheels off ground to turn the shaft/wheels.

Okay my mistake as I did not remove the bolt it was just loosened. I work with wood chisels but I get the idea something to spread joint.

Is there a good place to break steering shaft, does it matter which spline they all appear tight fitting into a split fittings. Maybe I just need different tool to spread joint.

If you read wiring diagrams they change colors at the blocks sometimes, so be it. I pulled those wires through bulkhead will be able to unwrap check all wires. I was looking through boxes & boxes of unmarked parts looking for door hinges 2 got lost.

Just about ready pull it all through.

Why do you think Land Rover installed disc in the front & drums in the rear? Xmod of which has larger brake in front. Saved me from a accident must be good.

That’s the way…..

Any advice getting the wiring blocks apart? Otherwise I pull on them daily add some oil been fourty years since installed.

For the doors you can buy barrels all keyed the same & exchange them for what you have. You may be able to do same for ignition depending on model, type of ignition key.

I was thinking that was a double wall would get stuck, well the hard jobs are easy the easy jobs are difficult.

Thanks I will be pushing every thing back into cab area then clean inspect wiring

Assuming the plug on wire loom fits through hole in bulkhead & assuming the rubber dognut through bulkhead should be replaced?